SAGD is a thermal recovery process in which steam oil ratio, SOR, is a key parameter that can affect the economic outcome of the process. Reservoirs with underlying or overlying lean bitumen present challenges for SAGD as they can act as a heat sink. Water has higher heat capacity than the bitumen and thus requires more steam to heat up the reservoir leading to higher SOR. The potential outcome of operating SAGD in these conditions may be lower bitumen rate and higher steam injection rate, both of which affect plant throughput and thus the economic matrix of SAGD. This paper looks at the performance of SAGD process in the presence of top lean bitumen. It will examine the theoretical CSOR that is needed to produce the bitumen with different

   The study was conducted to evaluate the antibacterial activity of water and alcoholic extracts (cold and hot) of plant Zingiber officinale against different types of bacteria includeing (Staphylococcus aureus ØŒ Staphylococcus epidermis ØŒ Escherichia coli ØŒ Pseudomonas aeruginosa
  ØŒProteus spp.and Klebsilla pneumoniae).  High effect of the hot (water and alcoholic) extracts of plant Zingiber officinale was on the different types of bacteria.          Investigation of presence of active compounds (Alkaloids, Glycoside, Tannins, Saponine and Resine) in this plant parts was carried out.        Sensitivity test of the isolate

Abstract

       The grey system model GM(1,1) is the model of the prediction of the time series and the basis of the grey theory. This research presents the methods for estimating parameters of the grey model GM(1,1) is the accumulative method (ACC), the exponential method (EXP), modified exponential method (Mod EXP) and the Particle Swarm Optimization method (PSO). These methods were compared based on the Mean square error (MSE) and the Mean Absolute percentage error (MAPE) as a basis comparator and the simulation method was adopted for the best of the four methods, The best method was obtained and then applied to real data. This data represents the consumption rate of two types of oils a he

A laboratory experiment was carried out at the College of Agriculture University of Baghdad in 2017. The aim was to improve the anatomical and physiological traits of broad bean seedling under salt stress by soaking it in salicylic acid. The concentrations of salicylic acid were 0, 10, and 20 mg L-1 and the electrical conductivity levels were 0, 3, and 6 dS m-1. The complete randomized design was used with four replications. The increasing of salicylic acid concentration up to 10 mg L-1 led to increasing the stem cortex thickness, stem vascular bundles thickness, and root cortex thickness significantly by (34.9,36.7,and 55 μm) respectively, while the treatment of 20 mg L-1 led to decreasing these traits by (28.2, 27.8, and 48.1 μm), compa

The experiments were conducted in laboratory conditions of a temperature of 25± 2C and relative moisture of 40± 5 % to evaluate the effectiveness of the cinnamon, lavender and clove essential oils on some biological life aspects of cowpea beetle, C. maculates. Results of the obligative experiment for the effect of the oils on insect adult killing showed that the concentration of 5% caused a mortality percentage averaged 13.33% of the insect males. The mortality percentage of the insect females was 11.3% for the cinnamon and lavender oils. The lavender oil had the lowest effect on adult killing, not exceeding 0. For the effect of the oils on egg laying, clove oil affected the number of eggs highly at the concentration of 5%, result

The experiments were conducted in laboratory conditions of a temperature of 25± 2C and relative moisture of 40± 5 % to evaluate the effectiveness of the cinnamon, lavender and clove essential oils on some biological life aspects of cowpea beetle, C. maculates. Results of the obligative experiment for the effect of the oils on insect adult killing showed that the concentration of 5% caused a mortality percentage averaged 13.33% of the insect males. The mortality percentage of the insect females was 11.3% for the cinnamon and lavender oils. The lavender oil had the lowest effect on adult killing, not exceeding 0. For the effect of the oils on egg laying, clove oil affected the number of eggs highly at the concentration of 5%, result

IRA Dawood, JOURNAL OF SPORT SCIENCES, 2016 - Cited by 3

A laboratory experiment was carried out in the laboratories of College of Agricultural Engineering Sciences, University of Baghdad in 2017. Three factors were studied; Sorghum bicolor L. cultivars (Inqath, Rabeh and Buhoth70), primed and unprimed seed, and salt stress (0, 6, 9 and 12 dS.m−1). The aim was to improve germination and seedling growth under salt stress. The results showed significant superiority of Buhoth70 cultivar compared to others, significantly superiority of primed seed compared to the unprimed and significant negative impact as long as increasing levels of salt stress at germination ratio, plumule length, dry seedling weight and seedling vigor index. The interaction between cultivars, priming and salt stress showed that

One of the most important challenges facing the development of laser weapons is represented by the attenuation of the laser beam as it passed through the layers of atmosphere.This paper presents a theoretical study to simulate the effect of turbulence attenuation and calculates the decrease of laser power in Iraq. The refractive index structure C_n^2 is very important parameter to measure the strength of the atmospheric turbulence, which is affected by microclimate conditions, propagation path, season and time in the day. The results of measurements and predictions are based on the Kolmogorov turbulence theory. It was demonstrated by simulations that the laser weapons in Iraq were severely affected due to the large change in temperatures,

In current research Copper was employed for preparing a ternary system of Al–Si alloy in different (0.2–2.5 wt. %) the best was taken is (1.5%wt) of copper that circumstances of solidification for improving the mechanical performance of the available in aluminium alloy. Cast iron molds were prepared to obtain tensile strength testing specimens. Alloys were prepared by employing gas furnaces. The molten metal was poured into a preheated cast-iron mold. The obtained alloy structures were studied using an X-ray diffractometer and optical microscopy. The mechanical performance of the prepared alloys was examined under the influence of different hardening conditions in both heat and non-heat-treated conditions. The outcomes showed at the