In this study, a one-dimensional model represented by Butler-Volmer-Monod (BVM) model was proposed to compute the anode overpotential and current density in a mediator-less MFC system. The system was fueled with various organic loadings of real field petroleum refinery oily sludge to optimize the favorable organic loading for biomass to operate the suggested system. The increase in each organic loading showed higher resistance to electrons transport to the anode represented by ohmic loss. On the contrary, both activation and mass transfer losses exhibited a noticeable decrement upon the increased organic loadings. However, current density was improved throughout all increased loads achieving a maximum current density of 5.2 A/m³

This work presents the modeling of the electrical response of monocrystalline photovoltaic module by using five parameters model based on manufacture data-sheet of a solar module that measured in stander test conditions (STC) at radiation 1000W/m² and cell temperature 25 . The model takes into account the series and parallel (shunt) resistance of the module. This paper considers the details of Matlab modeling of the solar module by a developed Simulink model using the basic equations, the first approach was to estimate the parameters: photocurrent I_ph, saturation current I_s, shunt resistance R_sh, series resistance R_s, ideality factor A at stander test condition (STC) by an ite

Abstract

This paper concerned with study the effect of a graphite micro powder mixed in the kerosene dielectric fluid during powder mixing electric discharge machining (PMEDM) of high carbon high chromium AISI D2 steel. The type of electrode (copper and graphite), the pulse current and the pulse-on time and mixing powder in kerosene dielectric fluid are taken as the process main input parameters. The material removal rate MRR, the tool wear ratio TWR and the work piece surface roughness (SR) are taken as output parameters to measure the process performance. The experiments are planned using response surface methodology (RSM) design procedure. Empirical models are developed for MRR, TWR and SR, using the analysis

Limestones have considerable commercial importance because they are used as building stones and are widely used for flooring and interior and exterior facings. On the other hand, the reserve calculation reveals the economic effectiveness of the investigation. This study aims to calculate the reserve of the middle Miocene limestone for engineering purposes. The limestone beds of the Nfayil Formation in Central Iraq have been studied over 15 outcrop sections. The Nfayil bed has an average thickness of about 1.64 m, while the overburden has an average of about 0.93 m. The average bulk density of limestone is 2.1 gm/cm3 . Kriging and triangulation method has been adopted and used in the calculation and assessment of reserve. The industrial laye

Background; paraphilias were studied in the sex
clinic, at Al-Rashad teaching mental hospital, in the
years 2009-2010, a subject never touched before in the
field of psychiatry in Iraq.
Aims of the study :
1-to identify the prevalence of types and number of
paraphilias in those patients.
2-to study the relationship of paraphilias with
sociodemographic factors of the patients.
Patients and methods; using the diagnostic criteria of
DSM IV TR, 52 patients from the outpatient sex clinic
at Al-Rashad mental hospital, collected and studied (41
males and 11 females).
Results; the ratio of men to women was 3.7 : 1, the
majority of our sample was in the age range of 21-30
years (36.35%), with a limited

A total of 28 birds were examined to investigate about the distribution of the nematode Hadjelia truncata among some members of the avian family Columbidae in Al-Diwaniya Province, Central Iraq. The percentages of the infection rate with this nematode were 27.27, 37.5, 14.28 and 0 in Columba livia, C. palumbis, Streptopelia decaocto, and S. turtur respectively. Reporting Hadjelia truncata from Streptopelia decaocto constitutes a new host record.

  From September 2002, monthly samples of common carp (Cyprinus carpio L.) were collected from two stations al AL-Gharraf canal. The results of this study revealed that the relationship between fecundity and total length , body weight and age can be  expressed by the following equations:  Log F=2.049+1.059 Log W.     r =0.98 Log F=1.173+2.534 Log L.     r =0.96 Log F=3.844+2.197 Log A.     r =0.87 The range of the absolute fecundity of 20 female fishes were 50910 – 1008514 eggs and the relative fecundity was 177 eggs/g. The average egg diameter was 1.52 mm in ripe female and it ranged from 0.99mm to 1.64mm. There were three peaks of Ganado somatic index in

Objective: To assess the clinical learning environment and clinical training for students' in maternal and child
health nursing.
Methodology: A descriptive study was conducted on non probability sample (purposive) of (175) students' in
Nursing College/ University of Baghdad for the period of June 19th to July 18th 2013. A questionnaire was used as a
tool of data collection to fulfill with objective of the study and consisted of three parts, including demographic,
clinical learning environment and clinical training for students' in maternal and child health nursing. Descriptive
statistical analyses were used to analyze the data.
Results: The results of the study revealed that the 65.1% of student at age which ranged b

In this article, the nonlinear problem of Jeffery-Hamel flow has been solved analytically and numerically by using reliable iterative and numerical methods. The approximate solutions obtained by using the Daftardar-Jafari method namely (DJM), Temimi-Ansari method namely (TAM) and Banach contraction method namely (BCM). The obtained solutions are discussed numerically, in comparison with other numerical solutions obtained from the fourth order Runge-Kutta (RK4), Euler and previous analytic methods available in literature. In addition, the convergence of the proposed methods is given based on the Banach fixed point theorem. The results reveal that the presented methods are reliable, effective and applicable to solve other nonlinear problems.

  This research studies the effect of grain size for the final stage in sintering Al2O3 .The experimental results for α- Al2O3 powder are modeled using ( L2-Regression ) technique in  order to study the effect grain size distribution on densification rate using four kinds for the initial particle size which were ( 1.44 , 2.54 , 0.7-2.54 ,1.15-3.53 ) µm , and for sintering time  (0-241) min. The mathematical simulation for grain size changing shows that the densification rates boots up as the grain size goes lower, this was due to the increase of contact area between the grains.