The Influence of x ratio and Annealing Temperatures on Structural and Optical Properties for (CuO)<sub>x</sub>(ZnO)<sub>1-x</sub> Composite Thin Films Prepared by PLD
(5)
(5)
Publication Date
Mon Aug 04 2014
Journal Name
Photonic Sensors
(9)
(6)
Publication Date
Wed May 29 2019
Journal Name
Iraqi Journal Of Physics
Synthesis and characterization of Iron tungstate oxide films by advanced controlled spray pyrolysis technique
FeWO4
semiconductor oxides
thin film
advance spray pyrolysis method
microstructure characterization.
For the first time Iron tungstate semiconductor oxides films (FeWO4) was successfully synthesized simply by advanced controlled chemical spray pyrolysis technique, via employed double nozzle instead of single nozzle using tungstic acid and iron nitrate solutions at three different compositions and spray separately at same time on heated silicone (n-type) substrate at 600 °C, followed by annealing treatment for one hour at 500 °C. The crystal structure, microstructure and morphology properties of prepared films were studied by X-ray diffraction analysis (XRD), electron Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) respectively. According to characterization techniques, a material of well-crystallized monoclinic ph
... Show More
Publication Date
Mon Dec 01 2014
Journal Name
Photonic Sensors
Crystalline Structure and Surface Morphology of Tin Oxide
Films Grown by DC Reactive Sputtering
Keywords: Sputtering
reactive sputtering
thin films
tin oxide
Abstract: Tin oxide thin films were deposited by direct current (DC) reactive sputtering at gas pressures of 0.015 mbar – 0.15 mbar. The crystalline structure and surface morphology of the prepared SnO2 films were introduced by X-ray diffraction (XRD) and atomic force microscopy (AFM). These films showed preferred orientation in the (110) plane. Due to AFM micrographs, the grain size increased non-uniformly as the working gas pressure increased.
Publication Date
Sat Mar 01 2008
Journal Name
Al-khwarizmi Engineering Journal
Minimizing error in robot arm based on design optimization for high stiffness to weight ratio
In this work the effect of choosing tri-circular tube section had been addressed to minimize the end effector’s error, a comparison had been made between the tri-tube section and the traditional square cross section for a robot arm, the study shows that for the same weight of square section and tri-tube section the error may be reduced by about 33%.
A program had been built up by the use of MathCAD software to calculate the minimum weight of a square section robot arm that could with stand a given pay load and gives a minimum deflection. The second part of the program makes an optimization process for the dimension of the cross section and gives the dimensions of the tri-circular tube cross section that have the same weight of
... Show MorePublication Date
Sun Jan 01 2023
Journal Name
Plant Archives
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION AND GERMINATION OF DATE PALM CV BARHI BY USING CELL SUSPENSION CULTURE TECHNIQUEe
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION AND GERMINATION OF DATE PALM CV BARHI BY USING CELL SUSPENSION CULTURE TECHNIQUEe
Publication Date
Thu Oct 01 2020
Journal Name
August
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION
AND GERMINATION OF DATE PALM BARHI C.V BY USING CELL
SUSPENSION CULTURE TECHNIQUE
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION AND GERMINATION OF DATE PALM BARHI C.V BY USING CELL SUSPENSION CULTURE TECHNIQUE
Publication Date
Fri Mar 27 2020
Journal Name
Plant Archives 20 (supplement 1), 1666-1670
Publication Date
Fri Mar 20 2020
Journal Name
Plant Archives (09725210) 20 (2)
Publication Date
Mon Apr 06 2020
Journal Name
August
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION
AND GERMINATION OF DATE PALM CV BARHI BY USING CELL
SUSPENSION CULTURE TECHNIQUE
This study was done to examine different concentrations of mercuric chloride (Hgcl2) for Explants sterilization and different
concentration of NAA) mg/L with 2iP for their effect on initiation primary callus and subsequent embryogenesis in Phoenix
dactyliferae cultivar Barhi. Leaf primordial and shoot tips were excised from 2-3 years old offshoot. The result showed that
contamination percentage decreased with an increase in concentration of Hgcl2 for two explants where in the control (0.0)%
gave highest value 75% and 62.5% of contamination for leaf primordial and shoot tip respectively while the addition (0.1)%
gave a significant decrease 37.5 and 0% for explants respectively. The Explants were inoculated onto Murashiege and Skoog
1962 (MS) medium supplemented with 2iP 3mg/L and containing 0
25
50 or 100 mg/L of NAA
the addition (50) mg/L of NAA
gave highest value 68.8% in percentage of callus initiation with significant difference from addition 0% gave lowest value
(18.8)%
as well Explants of shoot tip gave significant difference was 53.1% while leaf primordial gave 28.1%
Primary callus
was transferred to fresh MS medium containing (0
5
10 and 20) mg/L of NAA with 3mg/L 2iP
Results were recorded after 12
weeks. A highest value of embryonic callus induction percentage or fresh weight and dry weight 87.5% or 1.56g and 0.47g for
the character respectively for the treat 20 mg/L while control treatment 0.0 gave the lowest value 12.5% or 0.37g and 0.14g for
same character respectively. Inoculated 1g fresh biomass into a 250 ml Erlenmeyer flask containing 50 ml MS liquid medium
supplemented with NAA 20mg/L and agitated at 150 rpm by shaker to making suspension culture the measurements of
packed cell volume ( pcv) or fresh and dry weight taken weekly for 12 weeks
maximum values were reached in the eighth week
of PCV and fresh weight but the dry weight reached to highest value in seventh week
then the curve began to decline
gradually until it reached stability in the last two weeks. The cell suspension was Diluted to different initial cell density of 100
500
10000
50000 and 100000 cells /ml with hemocytometer. The initial cell number of (10000) cells gave significant different
of plating efficiency PE (11.6)% while (100) cells gave lowest value 1.8% of PE.
Publication Date
Fri Jul 01 2016
Journal Name
Journal Of Engineering
Study the Properties of Sodium Silicate Composite as a Barrier Separating Between the Internal Oil Distillation Towers and Chemical Fumes of Crude Oil
Sodium Silicate Composite as a Barrier Separating Between the Internal Oil Distillation Towers and Chemical Fumes of Crude Oil
The study of surface hardness, wear resistance, adhesion strength, electrochemical corrosion resistance and thermal conductivity of coatings composed from sodium silicate was prepared using graphite micro-size particles and carbon nano particles as fillers respectively of concentration of (1-5%), for the purpose of covering and protecting the oil distillation towers. The results showed that the sodium silicate coating reinforced with carbon nano-powder has higher resistance to stitches, mechanical wear, adhesive and thermal conductivity than graphite/sodium silicate composite especially when the ratio 5% and 1%, the electrochemical corrosion test confirmed that the coating process of stainless steel 304 lead to increasin
... Show More