The instant global trend towards developing tight reservoir is great; however, development can be very challenging due to stress and geomechanical properties effect in horizontal well placement and hydraulic fracturing design. Many parameters are known to be important to determine the suitable layer for locating horizontal well such as petrophysical and geomechanical properties. In the present study, permeability sensitivity to stress is also considered in the best layer selection for well placement. The permeability sensitivity to the stress of the layers was investigated using measurements of 27 core sample at different confining stress values. 1-D mechanical earth model (MEM) was built and converted to a 3-D full-field geomechanical model to reach perfect layer choice. The analysis of results has diagnosed the maximum horizontal stress direction of NE-SW as determined using both Fullbore Formation Micro Imager FMI and sonic scanner anisotropy analysis. The effect of porosity and permeability compaction as a result of stress changes while reservoir depletion is including on the reservoir simulation model. The choice of best layer and optimum design criteria for hydraulic fracturing is done in the current study using a compaction simulation model with the results of available measurements of geomechanical properties. The results of the simulation model show that the formation sensitivity to stress is an important factor for detecting a suitable layer for horizontal wells placement. The results of MEM indicate that horizontal stress difference (Δσ) and unconfined compressive strength (UCS) are the most important factors among geomechanical parameters affected the layer selection. From simulation results, it was found that 225 to 275 m fracture half-length gives a higher increment in oil production. The optimum number of fracture stages is noticed to be 8 to 10 stages after which the increment in production will reduce.
A nanocrystalline CdS thin film with 100 nm thickness has been prepared by thermal evaporation technique on glass substrate with substrate temperature of about 423 K. The films annealed under vacuum at different annealing temperature 473, 523 and 573 K. The X-ray diffraction studies show that CdS thin films have a hexagonal polycrystalline structure with preferred orientation at (002) direction. Our investigation showed the grain size of thin films increased from 9.1 to 18.9 nm with increasing the annealing temperature. The optical measurements showed that CdS thin films have direct energy band gap, which decreases with increasing the annealing temperature within the range 3.2- 2.85 eV. The absorbance edge is blue shifted. The absorption
... Show More) were taken from three stations at Al-Razzazah lake,by using a range of gill nets and seine nets. A total of 318 fish were taken from all stations. The age data determined from the scales showed that there were eight age classes present in station 1 and 2 and seven age classes in station 3. The increment in length of A. latus at the area of study showed a tendency to decrease with the increase in age after the fourth year of life. The length- weight relationships of both sexes specimens are expressed by the following equations: Log ï· = -1.93 + 2.67 Log ï¬â€¦.. for station (1) fish Log ï·= -2.08 + 2.74 Log ï¬ â€¦. For station (2) fish Log ï·= -2.02 + 2.39 Log ï¬ â€¦. For station (3) fish&n
... Show MoreSeveral new derivatives of 1,3,4-oxadiazoles and 1,2,4-triazoles linked to 3,4,5,6-tetrachlorophthalimide moiety were synthesized through following multisteps. The first step involved preparation of 3,4,5,6-tetrachlorophthalimide via reaction of 3,4,5,6-tetrachlorophthalic anhydride with urea at high temperature. Treatment of the resulted imide with ethyl chloroacetate in the second step afforded tetrachlorophthalimidyl ester which inturn was introduced in reaction with hydrazine hydrate in the third step, producing the corresponding acetohydrazide. The synthesized acetohydrazide was introduced in different synthetic paths including treatment with phenyl isothiocyanate or reaction with carbon disulfide in alkaline solution then with hydr
... Show MorePathogenic bacteria from samples of Al-Rystimya municipal wastewater treatment plant(third expansion)were isolated and identified .Samples were collected from the final disposal point at Dyala River. The duration of this study about five months from august up to December 2001 .The study was Focused upon pathogenic bacteria which have bad influency on health especially acute diarrhea which transferred by water. The bacterial species is isolated were: Escherichia coli , Enterobacter aerogenes , Shigella sp , Salmonella sp , Klebsiella sp, Pseudomonus sp, Aeromonus sp, and Vibrio cholera, Clostridium perifringens. Also some of the chemical and biological characteristics of the wastewater like COD, BOD,TSS, and total values were 660 ,450 ,65
... Show MoreThe current study included the separation of three alkaloid compounds from Anastatica Hierochuntica and studied the effect of the these compounds on cancerous cells , specifically liver cancer it was found that compound number one is the most influential or inhibiting at 50 percent followed by compound number three when using concentration of 400 μg/mL.
The study aims to identify the symptoms of PTSD among displaced Yazidi women according to age, marital status, educational level, and type of status (displaced or survivor). The study also seeks to identify the effect of the relaxation program on reducing PTSD among displaced Yazidi women. The research sample included (60) Yazidis for the statistical analysis sample and (5) for the experimental sample in the Dohuk governorate. For achieving the research objectives, a scale was used from the PTSD Checklist for DSM-5 (PCL-5), as well as a relaxation program was prepared. The researchers reached the following results that there is an average level of PTSD symptoms among displaced Yazidi women, there are no statistically significant differen
... Show MoreBackground The application of nanotechnology to biomedical surfaces is explained by the ability of cells to interact with nanometric features. The aim of this study was to consider the role of nanoscale topographic modification of CPTi dental implant using chemical etching method for the purpose of improving osseointegration. Materials and methods: Commercial pure titanium rod was machined into 20 dental implants. Each implant was machined in diameter about 3mm, length of 8mm (5mm was threaded part and 3mm was flat part). Implants were prepared and divided into 2 groups according to the types of surface modification method used: 1st group (10 implant) remained without nano surface modification (control), 2nd group include (10 implant) etche
... Show MoreThe effect of laser radiation on human aorta, coronary, and pulmonary arteries, and pulmonary veins has been investigated. Xenon-Chloride (eximer), Nitrogen, and Nd-YAG pulsed lasers of wavelengths 308, 337, and 1060 nm respectively were used. Their effects on fresh postmortem tissues, normal and diseased, was studied. The diameter and depth of ablation of the exposed tissues, in air, were measured as a function of many factors related to the type of laser and nature of the tissue. The effect of properties of the applied lasers, such as average power density and deposited energy density, on the exposed tissue surface were studied. The increase of these two parameters cause an increase in the depth and diameter of ablation. However the di
... Show MoreIn this work, has been a studied the effect of thermal treatment using different annealing temperatures (373, 423 and 473) K in vacuum on structural and morphological properties of organic semiconductor Alq3:C60 thin films which are prepared by the spin coating on a glass, silicon and porous silicon. These films have been coated on substrates with speed of 2000 rpm. The structure properties of Tris(8-hydroxyquinoline) aluminum (III) (Alq3) and fullerene (C60) (100:1) and (100:10) blend as-deposited and treated have been studied by X-ray diffraction (XRD) for glass only and morphological properties by Atomic Force Microscope (AFM) for silicon and porous silicon substrates. The results of X
... Show MoreThis experiment was carried out in one of the fields (A) affiliated to the College of Agricultural Engineering Sciences / University of Baghdad, for the spring season 2021, On hybrid tomato plants (Mayai Mayai) to test flower viability, using two factors, the first was three levels of irrigation interval (2, 4, 6) days, and the second factor three concentrations of compound Nano fertilizer with concentrations (0, 1.5, 2.5) gm liter-1, so that the number of treatments is 9 treatments and three replications, the number of experimental units is 27 experimental units distributed randomly according to the random drawing method to ensure reducing experimental error and obtaining the most accurate results. A factorial experiment 3 x 3 x 3 was carr
... Show More