In the present work, the focusing was on the study of the x-ray diffraction, dielectric constant, loses dielectric coefficient, tangent angle, alter- natively conductivity and morphology of PET/BaTio3. The PET/BaTio3 composite was prepared for polyethylene terephthalate PET polymer composite containing 0, 10, 20, 30, 40, 50, and 60 wt. % from Barium titanate BaTi03 powder. The composite of two materials leads to form mixing solution and hot-pressing method. The effect of BaTio3 on the structure and dielectric properties with morphology was studied on PET matrix polymer using XRD, LCR meter and SEM.
This research sheds light on the contributions of a group of scientific Kurdish scholars in the seventh and eighth Hijri centuries, who devoted themselves to serving science with the bad political and economic conditions at the time, and the research pointed to the flowering of science and how students travel in order to provide them with science, obtain a scientific certificate, then take up The research efforts of the scholars in the two Hijri century mentioned in the science of the Qur’an, whether in the field of recitations, intonation or interpretation, and the research ends with a conclusion in which I mentioned the most important conclusions reached in this research.
This study aims to predict the organic pollution produced from the presence of some polycyclic aromatic hydrocarbons (PAHs) and determination it's concentrations (µg/L , ppb) in Tigris river water by a collection twenty-seven water samples from a selected three stations with nine sampling sites and three depths of water (5 cm , 2 m and 4 m) each site for 4.6 km distance of a geographic studied area which is located between the ( Al-Senak and AL-Sarrafiah bridges ) at Baghdad city – Iraq on May, 2012. The geographic location was determined with a Global Positioning System (GPS) and Geographic Information System (GIS) software program. The concentrations of fourteen components (PAHs) were performed using the reverse phase
... Show MoreThe present research aims to study the effect of friction stir welding (FSW) parameters on temperature distribution and tensile strength of aluminum 6061-T6. Rotational and traverse speeds used were (500,1000,1400 rpm) and (14,40,112 mm/min) respectively. Results of mechanical tests showed that using 500rpm and 14mm/min speed give the best strength. A three- dimensional fully coupled thermal-stress finite element model via ANSYS software has been developed. The Rate dependent Johnson-Cook relation was utilized for elasto-plastic work deformations. Heat-transfer is formulated using a moving heat source, and later used the transient temperature outputs from the thermal analysis to determine equivalent stresses in the welde
... Show MoreThe synthesis of the MBIB ligand by the reaction of the BIB ligand with methionine in 1:1 ratio, and the metal complexes with Ni(II), Cu(II), and Pt(IV) were described. All synthesized compounds were characterized using spectroscopic methods such as FT-IR, 1H NMR, UV-VIS, thermal analysis (TG and DSC), atomic absorption (AAS), elemental microanalysis (C.H.N.S), melting point (m.p.), magnetic susceptibility, molar conductivity measurements, and chloride content. All the complexes were electrolytes, and the suggested geometric shapes for the complexes were octahedral. The magnetic properties of the platinum complex were diamagnetic, while those of the nickel and copper complexes were paramagnetic. All synthes
... Show MoreA reinforced concrete frame is referred as "RIGID FRAMES". However, researches indicate that the Beam-Column joint (BCJ) is definitely not rigid. In addition, extensive research shows that failure may occur at the joint instead of in the beam or the column. Joint failure is known to be a catastrophic type which is difficult to repair.
This study was carried out to investigate the effect of hoops and column axial load on the shear strength of high-strength fiber reinforced Beam-Column Joints by using a numerical model based on finite element method using computer program ANSYS (Version 11.0). The variables are: diameter of hoops and magnitude of column axial load.
The theoretical results obtained from ANSYS program are in a good a
The experiment was carried out in the wooden canopy in the green garden of Biology Department , College of Education for Pure Science – Ibn AL –Haitham, Baghdad University, during the growing season of 2012- 2013 , to study the influence of foliar application of three concentrations of zinc (0,50,75)mg. L ¯¹ with four concentrations of boron (0, 25, 50, 75) mg. L¯¹ and their interactions on some growth parameters of vegetative part of chickpea plant. The experiment was designed according to Randomized Completely Block Design(RCBD)with three replications, results indicated that:- 1- Foliar application of zinc and boron caused a significant increase in the averaye of dry weight for t
... Show MoreRifampicin (RF) considered a hepatotoxic drug. Is one of the first line successful drugs of management of tuberculosis. To reduce injury and protect liver from adverse effect of Rifampicin, this study was designed to investigate the activity of Nigella Sativa (NS) seeds powder aqueous suspension to hepato protection against Rifampicin.
For conducting this study,24 male albino rats were divided into four groups and all treated orally as follow; group І (control), received normal saline alone; group II, received RF (50mg/kg body weight/day); group III received NS it's called normal dose, (2g/kg body weight day); group IV RF (50mg/kg body weight) + NS (2g/kg body weight).Respectively for 28 days. Blood samples obtained for estimation of
A study of the effects of the discharge (sputtering) currents (60-75 mA) and the thickness of copper target (0.037, 0.055 and 0.085 mm) on the prepared samples was performed. These samples were deposited with pure copper on a glass substrate using dc magnetron sputtering with a magnetic flux density of 150 gauss at the center. The effects of these two parameters were studied on the height, diameter, and size of the deposition copper grains as well as the roughness of surface samples using atomic force microscopy (AFM).The results of this study showed that it is possible to control the specifications of copper grains by changing the discharge currents and the thickness of the target material. The increase in discharge curre
... Show MoreTen new thiourea derivatives 1-10 were prepared in this work using a two-step process that involved reacting 4-methoxybenzoyl chloride with KSCN to afford 4-methoxybenzoyl isothiocyanate. This was followed by reaction with various amines (primary amines, secondary amines, and diamines) to give the aforementioned title products 1-10. These products were characterized by FT-IR, 1H NMR and 13C NMR spectroscopy. Using the DPPH scavenging method, the antioxidant activity of thiourea products was investigated, and derivative 8 had the greatest antioxidant activity in comparison to the other derivatives. Moreover, molecular dockin
... Show More