The fluorescence emission of Rhodamine 6G (R6G) and Acriflavine dyes in PMMA polymer have been studied by changing the irradiation and exposure time of laser light to know the effect of this parameter. It was found that the fluorescence intensity decreases in the polymer samples doped dyes as the exposure time increases and then reaches stabilization at long times, this behavior called photobleaching, which have been shown in liquid phase less than solid phase. Using 2nd harmonic with wavelength 530 nm laser, the photobleaching effect in the two dye-doped polymers different solvent but same was studied. It was observed that photobleaching of by different solution and by using dip spin coating the photobleaching seem in liquid phase more than the thin films from the mixing solutions with a thickness of (0.1 to 1 micrometer). The maximum peak of fluorescence seems as red shift with different solvent concentration.
One’s character is shaped by the family he/she has and the way he/she is raised up. Bad parents affect their children tragically, and the later consequences, the parents are the ones who pay for being bad ones. Tracy Letts explores the dark side of family life in his domestic play August: Osage County (2007), one of the most well-known contemporary plays of American theatre in the twenty-first century. The playwright presents the Westons as an embodiment of the image of family disconnected relationships due to bad parenting. Violet is a model of a bad mother who plays a prominent role in destroying her family. The impact of bad parenting is revealed in the circle of the formerly abused children who turned to be abusers of their children o
... Show MoreThe parameters of resistance spot welding (RSW) performed on low strength commercial aluminum sheets are investigated experimentally, the performance requirements and weldability issues were driven the choice of a specific aluminum alloy that was AA1050. RSW aluminum alloys has a major problem of inconsistent quality from weld to weld comparing with welding steel
alloys sheet, due to the higher thermal conductivity, higher thermal expansion, narrow plastic temperature range, and lower electrical resistivity. Much effort has been devoted to the study of describing the relation between the parameters of the process (welding current, welding time, and electrode force) and weld strength. Shear-tensile strength tests were performed to ind
Studies in Iraq that concerned identification of free-living Protozoa (sarcodina) are scarce; so the current study deals with these protozoan communities inhabiting the Tigris River in Baghdad City. Sampling collection stations have been selected at each of AL-Gheraiˈat and AL-Adhamiyah area adjacent to the river. Monthly intervals sampling with three samples were collected from each station from June to September 2020. Total of 23 sarcodina taxa were listed, out of them 5 taxa were new record to the Tigris River in Baghdad: Difflugia urceolata Carter, 1864 (Arcellinida, Difflugiidae), Heleopera perapetricola Leidy, 1879 (Arcellinida, Heleoperidae), Rhaphidiophrys pallida F.E. Schulze, 1874 (Centrohelida, Raphidiophridae), Saccamoeba sp
... Show MoreGypseous soil is considered as a problematic soil for embankment construction, however, implementation of emulsified asphalt as a stabilization agent could be a proper solution for enhancing its properties as a subgrade soil. In this work, the sustainability of asphalt stabilized soil has been assessed in terms of its resistance to cyclic (freezing-thawing) and (heating-cooling) processes. Specimens have been prepared at optimum fluid content (moisture and emulsion) and tested under direct shear stresses while subjected to 30 cycles of (freezing-thawing) and (heating-cooling). Both of dry and soaked testing conditions have been implemented. Data have been observed after each 10 cycles, and compared with that of reference mix. It was conclud
... Show MoreThe aim of this paper is to measure the characteristics properties of 3 m radio telescope that installed inside Baghdad University campus. The measurements of this study cover some of the fundamental parameters at 1.42 GHz. These parameters concentrated principally on, the system noise temperature, signal to noise ratio and sensitivity, half power beam width, aperture efficiency, and effective area. These parameters are estimated via different radio sources observation like Cas-A, full moon, sky background, and solar drift scan observations. From the results of these observations, these parameters are found to be approximately 64 K, 1.2, 0.9 Jansky, 3.7°, 0.54, and 3.8 m2 respectively. The parameters values have vital affect to quantitativ
... Show MoreLawful protection of the human gene conceded a moral concern regarding the future of existence human. After the discovery of the human genetic map, scientific experiments and research related to the human gene increased, negative applications of genetic engineering in particular that violate essential human rights, the right to human dignity to be specific. These practices represent actual challenges to the existence and diversity of current and future generations. Therefore, the presence of legal rules at the domestic and global levels is an absolute necessity to prohibit these threats and determine civil and criminal accountability for those who infringe any laws related to this issue.
This paper presents a numerical analysis using ANSYS finite element program to simulate the reinforced concrete slabs with spherical voids. Six full-scale one way bubbled slabs of (3000mm) length with rectangular cross-sectional area of (460mm) width and (150mm) depth are tested as simply supported under two-concentrated load. The results of the finite element model are presented and compared with the experimental data of the tested slabs. Material nonlinearities due to cracking and crushing of concrete and yielding of reinforcement are considered. The general behavior of the finite element models represented by the load-deflection curves at midspan, crack pattern, ultimate load, load-concrete strain curves and failure m
... Show MoreThe main objective of present work is to describe the feasibility of friction stir welding (FSW) for
joining of low carbon steel with dimensions (3 mm X 80 mm X 150 mm). A matrix (3×3) of welding
parameters (welding speed and tool rotational speed) was used to see influence of each parameter on
properties of welded joint .Series of (FSW) experiments were conducted using CNC milling machine
utilizing the wide range of rotational speed and transverse speed of the machine. Effect of welding
parameters on mechanical properties of weld joints were investigated using different mechanical tests
including (tensile and microhardness tests ). Micro structural change during (FSW) process was
studied and different welding zones