Solar photovoltaic (PV) system has emerged as one of the most promising technology to generate clean energy. In this work, the performance of monocrystalline silicon photovoltaic module is studied through observing the effect of necessary parameters: solar irradiation and ambient temperature. The single diode model with series resistors is selected to find the characterization of current-voltage (I-V) and power-voltage (P-V) curves by determining the values of five parameters ( ). This model shows a high accuracy in modeling the solar PV module under various weather conditions. The modeling is simulated via using MATLAB/Simulink software. The performance of the selected solar PV module is tested experimentally for differ

         The world's population growth and the increasing demand for new infrastructure facilities and buildings , present us with the vision of a higher resources consumption, specially in the form of more durable concrete such as High Performance Concrete (HPC) . Moreover , the growth of the world pollution by plastic waste has been tremendous. The aim of this research is to investigate the change in mechanical properties of HPC with added waste plastics in concrete. For this purpose 2.5%, 5% and 7.5% in volume of natural fine aggregate in the HPC mixes were replaced by an equal volume of Polyethylene Terephthalate (PET) waste , got by shredded PET bottles. The mechanical propert

The sensors based on Nickel oxide doped chromic oxide (NiO: Cr2O3) nanoparticals were fabricated using thick-film screen printing of sol-gel grown powders. The structural, morphological investigations were carried out using XRD, AFM, and FESEM. Furthermore, the gas responsivity were evaluated towards the NH3 and NO2 gas. The NiO0.10: Cr2O3 nanoparticles exhibited excellent response of 95 % at 100oC and better selectivity towards NH3 with low response and recovery time as compared to pure Cr2O3 and can stand as reliable sensor element for NH3 sensor related applications.

In this research, a selection of some mineral water was selected on the basis of being the most marketed by the owners of shops in Najaf province, with six types, where daily samples of this water were taken by 50 ml for two months from (1/11/2018 -1/1/2019). The following ions concentrations were measured (Br-, Cl-, F-, NO3-, SO42-, Na+, K+, Ca2+, Mg2+), pH and the electrical conductivity were measured and the results were compared with the allowable rates according to the international organizations. It was noted that they conform to international and Iraqi standards.

In this paper, experimental study has been done for temperature distribution in space conditioned with Ventilation Hollow Core Slab (TermoDeck) system. The experiments were carried out on a model room with dimensions of (1m 1.2m 1m) that was built according to a suitable scale factor of (1/4). The temperature distributions was measured by 59 thermocouples fixed in several locations in the test room. Two cases were considered in this work,  the first one during unoccupied period at night time (without external load) and the other at day period with external load of 800W/m² according to solar heat gain calculations during summer season in Iraq. All results confirm the use of TermoDeck system for ventilation and cooling/heat

Incremental forming is a flexible sheet metal forming process which is performed by utilizing simple tools to locally deform a sheet of metal along a predefined tool path without using of dies. This work presents the single point incremental forming process for producing pyramid geometry and studies the effect of tool geometry, tool diameter, and spindle speed on the residual stresses. The residual stresses were measured by ORIONRKS 6000 test measuring instrument. This instrument was used with four angles of (0º,15º,30º, and 45º) and the average value of residual stresses was determined, the value of the residual stress in the original blanks was (10.626 MPa). The X-ray diffraction technology was used to measure the residual stresses

This study presents the debonding propagation in single NiTi wire shape memory alloy into linear low-density polyethylene matrix composite the study of using the pull-out test. The aim of this study is to investigate the pull-out tests to check the interfacial strength of the polymer composite in two cases, with activation NiTinol wire and without activation. In this study, shape memory alloy NiTinol wire 2 mm diameter and linear fully annealed straight shape were used. The study involved experimental and finite element analysis and eventually comparison between them. This pull-out test is considered a substantial test because its results have a relation with behavior of smart composite materials. The pull-out test was carried out by a u

Verbs are an important material in the construction of the sentence, as they are among the requirements of every sophisticated language, and in this regard, Ibn Al-Gothic (d. 367 AH): “Know that verbs are the origins of the buildings of most speech, and thus scholars called them buildings.” Verbs are the source of expression of the speakers’ ideas to represent the element of activity and movement, and with their knowledge We infer the meanings of Arabic words, and Ibn Al-Sarraj (d. 316 AH) defined it: “The verb denotes a meaning and a time, and that time is either past, present, or future.” Its letters are original and does not drop from its construction a letter in the conjugation of its conjugations, and it is in Arabic two type

Recently, there has been a notable surge in interest surrounding entrepreneurial orientation and strategic entrepreneurship. These concepts are particularly relevant due to their modern characteristics that aid in adapting to the environment. They also play a crucial role in improving production, service, and technological processes to sustain value, minimize competition, and drive ongoing enhancements, ultimately leading to a position of leadership within public companies. Therefore, the primary focus of this research was to examine the influence of entrepreneurial orientation on achieving strategic entrepreneurship. This influence is further mediated by the presence Iraqi Ministry of Agric

In the contemporary political history of Iraq, a unique protest broke out on October 1st, 2019. This protest reappeared on October 25th and lasted up to the following weeks making this protest as the most comprehensive and deepest one. It has the possibility of lengthening and the diversification of methods among all the social protesting movements during the century for Iraq. This desperate youth movement presents various images and methods to highlight the image of the protesting movement. The role of the Iraqi woman was clear, which was embodied through the mural paintings expressing her artistic and social role in conveying and expressing the goal of the protest. The aim of the current research is to identify the social artistic implica