Saccharin is firstly synthesized in 1879. It is a very well-known as an inexpensive substitute for sugar as it is a non-caloric sweetener. The article shows the properties, use, metabolism and various synthesis and reactions of saccharine. Moreover, the toxicological reports explain that saccharin is mostly responsible for the bladder tumors observed in the male rats, the relationship between the consumption of saccharin and bladder cancer is afforded by epidemiological studies.  The benefit-risk evaluation for saccharin is hardly to indicate. Saccharin is a sugar substitute, frequently used either in food industry, or in pharmaceutical formulations and even in tobacco products. The chemistry of saccharin is inter

In this investigation, the mechanical properties and microstructure of Metal Matrix Composites (MMCs) of Al.6061 alloy reinforced by ceramic materials SiC and Al₂O₃ with different additive percentages 2.5, 5, 7.5, and 10 wt.% for the particle size of 53 µ_m are studied. Metal matrix composites were prepared by stir casting using vortex technique and then treated thermally by solution heat treatment at 530 ⁰C for 1 hr. and followed by aging at 175 ⁰C with different periods. Mechanical tests were done for the samples before and after heat treatment, such as impact test, hardness test, and tensile test. Also, the microstructure of the metal matrix composites was examine

In Baghdad governorate, samples of dried birds waste were obtained from poultry cages for investigate the of the presence of fungi. There was a high proportion of Candida spp., Rhodotorula spp. and filamentous fungi that obtained from the dry droppings. Al samples gave a positive results included 177 isolates, these isolates includes different Candida species 62 isolates (35.02%), Rhodotorula spp. 28 isolates (15.81%), and the following filamentous genera: Aspergillus spp. 50 isolates (28. 24%), (A. niger 20 isolate, A. flavus 18 isolate, A. fumigatus 12 isolate), Penicillium spp. 11 isolates (6.21%) and Mucor spp. 26 isolate (14.68%). The inhibitory effect of the used detergents (with concentration of 10-1 mg/ml.( was ranged from 35 mm

New tetradentate Schiff base [H2L] namely [2,2׳ -(ethane-1,2- diylbis (azan-1-ylylidene) diacetic acid)] was prepared from condensation of ethylenediamine with  glyoxylic acid  in ethanol as a solvent in presence of drops of 48% HBr .The structure of ligand (H2L) was characterized by,F-IR, U.V-Vis.,1H-,13C-NMR, pectrophotometer,melting point and elemental microanalysis C.H.N.  Metal complexes of the ligand (H2L) in general Molecular formula [M(L)(H2O)2], where M=  Co(II), Ni(II), Cu(II), Mn(II) and Hg(II); L=(C6H8N2O4) were synthesized were characterized by, Atomic absorption, F-IR, U.V-Vis. spectra, molar conductivity and magnetic susceptibility.It was found that all the complexes showed octahedral geometries.And

Copper oxide nanoparticles (CuO NPs) were synthesized by two methods. The first was chemical method by using copper nitrate Cu (NO3)2 and NaOH, while the second was green method by using Eucalyptus camaldulensis leaves extract and Cu (NO3)2. These methods easily give a large scale production of CuO nanoparticles. X-ray diffraction pattern (XRD) reveals single phase monoclinic structure. The average crystalline size of CuO NPs was measured and used by Scherrer equation which found 44.06nm from chemical method, while the average crystalline size was found from green method was 27.2nm. The morphology analysis using atomic force microscopy showed that the grain size for CuO NPs was synthesized by chemical and green methods were 77.70 and 89.24

Many researchers consider Homogeneous Charge Compression Ignition (HCCI) engine mode as a promising alternative to combustion in Spark Ignition and Compression Ignition Engines. The HCCI engine runs on lean mixtures of fuel and air, and the combustion is produced from the fuel autoignition instead of ignited by a spark. This combustion mode was investigated in this paper. A variable compression ratio, spark ignition engine type TD110 was used in the experiments. The tested fuel was Iraqi conventional gasoline (ON=82).

The results showed that HCCI engine can run in very lean equivalence ratios. The brake specific fuel consumption was reduced about 28% compared with a spark ignition engine. The experimental tests showed that the em

Nuclear structure of ^29-34Mg isotopes toward neutron dripline have been investigated using shell model with Skyrme-Hartree–Fock calculations. In particular nuclear densities for proton, neutron, mass and charge densities with their corresponding rms radii, neutron skin thicknesses and inelastic electron scattering form factors are calculated for positive low-lying states. The deduced results are discussed for the transverse form factor and compared with the available experimental data. It has been confirmed that the combining shell model with Hartree-Fock mean field method with Skyrme interaction can accommodate very well the nuclear excitation properties and can reach a highly descriptive and predictive power when investiga

Alloys of GaxSb1-x system with different Ga concentration (x=0.4, 0.5, 0.6) have been prepared in evacuated quartz tubes. The structure of the alloys were examined by X-ray diffraction analysis (XRD) and found to be polycrystalline of zincblend structure with strong crystalline orientation (220). Thin films of GaxSb1-x system of about 1.0 μm thickness have been deposited by flash evaporation method on glass substrate at 473K substrate temperature (Ts) and under pressure 10-6 mbar. This study concentrated on the effect of Ga concentration (x) on some physical properties of GaxSb1-x thin films such as structural and optical properties. The structure of prepared films for various values of x was polycrystalline. The X-ray diffraction analy

Thermomechanical analysis (TMA) and differential scanning calorimetry (DSC) are used to investigate the effect of molding and annealing of polyester on the behavior of thermal expansion and crystallization since these factors play role in the reprocessing or recycling of the polymer. The dynamic mode of the TMA provides enhanced characterization information about the polyester since it separates the transitions into reversible and irreversible signals, and also reveals the progress of the amorphous regions as the polyester loses strength with the increasing temperature approaching melting. Slow cooling after annealing brings crystallization that may be attributed to molecular chain straightening due to orientation.