A polycrystalline CdSe thin films doped with (5wt%) of Cu was fabricated using vacuum evaporation technique in the substrate temperature range(Ts=RT-250)oC on glass substrates of the thickness(0.8?m). The structure of these films are determined by X-ray diffraction (XRD). The X-ray diffraction studies shows that the structure is polycrystalline with hexagonal structure, and there are strong peaks at the direction (200) at (Ts=RT-150) oC, while at higher substrate temperature(Ts=150-250) oC the structure is single crystal. The optical properties as a function of Ts were studied. The absorption, transmission, and reflection has been studied, The optical energy gap (Eg)increases with increase of substrate temperature from (1.65

The eff ect of partial substitution for lanthanum (La) on the structural properties of the compound Y1-xLaxBa4Cu7O15+δ were studied. The variation of (x) are x=0.1, 0.2 and 0.3, which was synthesized by solid state reaction method. The mixed powder was pressed with pressure (7 ton / cm2) as a disc (1.5 cm) diameter and a thickness of (0.25 to 0.3 cm). The samples were sintering by 120 °C / hour with a changing rate from room temperature to 850 ° C through 72 hours. XRD analysis using to calculate crystal size, strain and degree of crystallinity. It was found all samples have orthorhombic structure and change of structure with increasing lanthanum concentration. It was shown that the change lanthanum concentrations of all our samp

The species Spongilla lacustris was identified for the first time in Iraq, it was found during winter 1998 in an irrigation canal within the campus of the University of Baghdad (Jadiriah), water is drawn from Tigris river. The specimens were found in water samples of sizes ranging between 5-50 cm with yellowish color . It was found in two habitats , one as attached on submerged aquatic plant Ceratophyllum sp., and the other on the canal bottom (concret material). Some physico- chemical characters were determined including conductivity ,salinity , pH, total alkalinity, total hardness, Ca ,Mg ,anddissolved oxygen. Water quality was fresh , alkaline, hard and well aerated.

The water scarcity that Iraq suffers from and the low irrigation efficiency in irrigation projects, therefore, it was necessary to evaluate the performance of the irrigation system of the western canal for the Ishaqi irrigation project in Salah al-Din Governorate to determine the water management strategies that can be used to improve the irrigation efficiency in the project. The performance of the field irrigation system was evaluated on two fields of different crops and irrigation methods according to the agricultural reality of the study area in the Western canal for the Al-Ishaqi Irrigation Project in Salah Al-Din Governorate. The fieldwork included measurements of the moisture content before and after irrigation, fi

The aim of this research is to develop mechanical properties of a new aluminium-lithium-copper alloy. This alloy prepared under control atmosphere by casting in a permanent metal mould. The microstructure was examined and mechanical properties were tested before and after heat treatment to study the influence of heat treatment on its mechanical properties including; modulus of elasticity, tensile strength, impact, and fatigue. The results showed that the modulus of elasticity of the prepared alloy is higher than standard alloy about 2%. While the alloy that heat treated for 6 h and cooled in water, then showed a higher ultimate tensile stress comparing with as-cast alloy. The homogenous heat treatment gives best fatigue

this paper give a proof of known conditions for the existence of peridic conincidence points of continuius maps using lindemann theotem on transcendental numbers

The study aims mainly to evaluate the performance of Sharq Dijila water treatment plant in removing turbidity for the period of 1-4-2001 to 31-3-2004. Daily data for turbidity of raw, clarified, filtered, and supplied water were analyzed. The results of the study showed that there is a wide variation in turbidity levels of raw water fluctuating between 10-1000 NTU with mean value of 41.3 NTU. Turbidity values of the clarified water varied between 1.4-77 NTU. Based on the turbidity value of 10 NTU and 20 NTU (the design maximum turbidity) the readings gave an acceptable percentage of 32.4% and 86% respectively. The turbidity of filtered water ranged between 0.2-4.5 NTU which are completely in compliance with Iraqi and WHO standards. In ac

Urban growth of cities is connected with three related problems, the first one, is the deterioration of the center, which is a mark for historical origin. The second is the emergence of city edge, which contradicts by the center. The third one is the rapid semi urbanism of the edge. Literature review showed that Baghdad historical center (Old Rusafa and Karkh) had grown in four morphological stages, during which main paths had been changed from those which were perpendicular to the river front to those parallel to it. Research problem is that “there is a knowledge gap about the direction and origin of paths within Baghdad old center, after its growth”. The first research hypothesis is, “the direction of paths within old Baghdad cen

            The aim of the current research is to measure the sense of coherence among individuals with physical disabilities. The researcher adopted a scale of (29) paragraphs spread over three domains designed by Antonovski (1993) to measure the sense of coherence. A sample of (210) disabled individuals was chosen randomly to collect the required data. The data were analyzed using the statistical package for social sciences (SPSS). The result showed a lack of sense of coherence among the sample.

The dynamic response of foundation rest on collapsible soil in dry and soaked states is studied through wide experimental programmed. Gypseous soil from Tikrit governorate area was obtained and subjected to various physical and chemical analysis to determine its properties. Steel rectangular footing (400x200x20) mm is manufactured. The machine is fitted to the footing, then the model machine foundation is placed centrally over the prepared soil layer in steel container (1200x 1000x1000)mm with proper care to maintain the center of gravity of whole system lie in the same vertical line with container.Then, the footing is subjected to vertical harmonic loading using a rotating mass type mechanical oscillator to simulate different dynamic lo