Tuaimah GS, AQ Al-Awadi, Ahmed ME., Effect of Cutibacterium acnes cell free antigen (CFAg) immunization, levofloxacin and cinnamon oil on Cutibacterium acnes infection in rabbits, Onl J Vet Res., 22 (9):811-822, 2018. C. acnes causes acne vulgaris most commonly in 12-24 year olds. Five albino rabbits were immunized at day 1 and 14 with Cutibacterium acnes cell free antigen (CFAg) and then infected intradermally with 0.1 ml C. acnes suspension (2×108 cfu/ml) at day 30. Two groups of five infected rabbits were then treated at Day 30 with 0.5% levofloxacin or 0.2% cinnamon oil twice daily for 12 days. Five control rabbits were infected intradermally with 0.1 ml 2×108 cfu/ml Cutibacterium acnes n (2×108 cfu/ml). At day 42, skin test (mm), se

      This study was designed to investigate the effect of sesame oil on lipid profile and liver enzyme in male albino rats treated with Carbone tetrachloride (CCl4).

    Forty adult male rats were divided into four equal groups, first group was daily administrated with tap water, the second group was injected with CCl4 (80mg/kg.BW/day), the third group was administrated with sesame oil (150mg/kg.BW/day) and the fourth group was injected with CCl4 (80mg/kg.BW/day) and was administrated with sesame oil (150 mg /kg.BW /day) for 30 days. The statistical  results of the present study showed a significant  (p<0.05) increase in the level of cholesterol , triglycerides and Low density

A comprehensive practical study of typical mechanical properties of welded Aluminum alloy AA7020-T6 (Al-Mg-Zn), adopting friction stir welding (FSW) technique and conventional metal inert gas (MIG) technique, is well achieved in this work for real comparison purposes. The essences of present output findings were concentrated upon the FSW samples in respect to that MIG ones which can be summarized in the increase of the ultimate tensile strength for FSW was 340 MPa while it was 232 MPa for MIG welding, where it was for base metal 400 MPa. The minimum microhardness value for FSW was recorded at HAZ and it was 133 HV0.05 while it was 70 HV0.05 for MIG weld at the welding metal. The FSW produce 2470 N higher than MIG welding in the bending t

This research aims to study the effect of microwave furnace heat on the mechanical properties and fatigue life of aluminum alloy (AA 2024-T3). Four conditions were used inside microwave furnace (specimens subjected to heat as dry for 30 and 60min. and specimens subjected to heat as wet (water) for 30 and 60 min.), and compared all results with original alloy (AA 2024-T3). Tensile, fatigue, hardness and surface roughness tests were used in this investigation. It is found that hardness of dry conditions is higher than wet conditions and it increases with increasing of time duration inside microwave furnace for dry and wet conditions. Also, tensile strength has the same behavior of hardness, but it increases with decreasing

The aim of this research is to develop mechanical properties of a new aluminium-lithium-copper alloy. This alloy prepared under control atmosphere by casting in a permanent metal mould. The microstructure was examined and mechanical properties were tested before and after heat treatment to study the influence of heat treatment on its mechanical properties including; modulus of elasticity, tensile strength, impact, and fatigue. The results showed that the modulus of elasticity of the prepared alloy is higher than standard alloy about 2%. While the alloy that heat treated for 6 h and cooled in water, then showed a higher ultimate tensile stress comparing with as-cast alloy. The homogenous heat treatment gives best fatigue

The banking sector has a significant impact on the economic growth of the country, and the importance of this sector must assess its financial performance from time to time, to measure the situation related to money for each bank and how to put the supervision of the efficiency of the full. The research aims at evaluating the financial performance according to the elements of the CAMELS model, which including capital adequacy, asset quality, management efficiency, profitability, liquidity, and market risk sensitivity. The research included the study of Al-Mansour Investment Bank during the period from 2014 to 2018. The base capital ratio was used to total assets to measure capital adequacy The proportion of investments to total a

Drilling with casing (DWC) can be considered as a modern drilling technique in which both of drilling and casing operations done in the same time by using the casing to transfer the hydraulic and mechanical power to the bit instead of traditional drilling string. To overcome oil well control, minimizing the total cost through enhancing drilling efficiency, drilling with casing was proposed as an enabling technology.

   Two surface sections (17 1/2 - and 12 1/4- inch) were drilled successfully in Rumaila oil field with  casing strings which reached 655m and 1524m measured depths respectively.

   By using DWC technique, the total drill/case phase time was reduced up to 20% comparing to conventional