In this paper the effect of engagement length, number of teeth, amount of applied load, wave propagation time, number of cycles, and initial crack length on the principal stress distribution, velocity of crack propagation, and cyclic crack growth rate in a spline coupling subjected to cyclic torsional impact have been investigated analytically and experimentally. It was found that the stresses induced due to cyclic impact loading are higher than the stresses induced due to impact loading with high percentage depends on the number of cycles and total loading time. Also increasing the engagement length and the number of teeth reduces the principal stresses (40%) and
(25%) respectively for increasing the engagement length from (0.15 to 0.23) and the number of teeth from (8 to 10). while increasing the other parameters (amount of applied load, wave propagation time, number of cycles, and initial crack length) increase the principal stresses at the root of the tooth (37% when the applied load rises from (8 KN to 11KN) and (62% when the wave
propagation time rises from (0.5 to 1).
The use of destructive weapons in wars without restrictions and controls, which eat green and dry land, pollute the environment and cause genocide, has become the problem of the times.
International conventions for the protection of the environment during armed conflicts are characterized by generality, ambiguity, and open to interpretation by the participating states in the agreement, and each state interprets these texts to serve its interests, but the Islamic Sharia stipulates the prohibition of the use of these comprehensive destructive weapons in an unambiguous manner, As stated in the Holy Quran:
... Show MoreThe study the problem emerged in the inability of local companies to enter the field of active competition with other companies operating in the same economic sector due to the high cost of their products, hence, the companies that want to apply this technique can effectively compete in order to achieve those objectives.
So this study focused on the goal of reducing the cost of products by reducing the cost product to a minimum , as the study was based in its hypothesis on the ability of companies to application this technique which in turn leads to increased profits under conditions of normal working and the power available and their potential in improving the quality of its products, as well as the need for full coordina
... Show MoreThe art of batik is one of the ancient arts that has a long history in East Asian countries, especially in Indonesia, where it was considered a traditional craft with which many Indonesian tribes lived. This art began to move to other continents and develops and progresses due to the artist’s connection to the surrounding technological and intellectual development, as art became more outgoing and liberated, it helped the artist to create and innovate in his designs. In this research, he focuses on modern performance methods through which print paintings can be produced through design elements, especially calligraphy, to create aesthetic and creative effects in the productive work. The current research aims to identify the various perfo
... Show MoreThe anatomical features of leaves and stems of seven species belonging to five genera of the Papaveraceae family were studied, including: Fumaria bracteosa Pomel, 1875; Glaucium grandiflorum Boissier & A. Huet,1856; Hypecoum pendulum Linnaeus, 1753; Papaver fugax Poiret,1804; Papaver macrostomum Boissier & A. Huet, 1867; Papaver rhoeas Linnaeus, 1753 and Roemeria refracta de Candolle,1821. The results showed that the anticlinal cell walls of the adaxial surface were more thickened in P. fugax, H. pendulum, P. macrostomum and R.refracta, while it was thin in P. rhoeas. The cur
... Show MoreThe research included five sections containing the first section on the introduction of the research and its importance and was addressed to the importance of the game of gymnastic and skilled parallel effectiveness and the importance of learning, but the problem of research that there is a difference in learning this skill and difficulty in learning may be one of the most important reasons are fear and fear of falling and injury, And a lack of sense of the movement of the movement is one of the obstacles in the completion of the skill and the goal of research to design a device that helps in learning the skill of descending Almtor facing with half a cycle according to the typical locomotor track on the parallel device of the technical men'
... Show MoreResearch includes three axes, the first is the average estimate time of achievement (day) to work oversight, to five supervisory departments in the Office of Financial Supervision Federal and then choose the three control outputs and at the level of each of the five departments above, and after analyzing the data statistically back to us that the distribution of the times of achievement It is the exponential distribution (Exponential Distribution) a parameter (q), and the distribution of normal (Normal Distribution) with two parameters (μ, σ2), and introduced four methods of parameter estimation (q) as well as four modalities parameter to estimate (
... Show MoreThis study is concerned with organizational learning and its impact on total quality management in the education sector. Organizational learning is a process that provides the educational sector with the ability to adapt and respond rapidly to developments and changes in a better way according to its main dimensions (Mental Models, Personal Mastery, Team Learning, Shared Vision, System Thinking) by adopting the philosophy of Total Quality Management (TQM) in accordance with its basic dimensions (leadership, customer satisfaction, participation of workers, continuous improvement, training and education). The main purpose of this study is to know (the impact of the Senge model of organizational learni
... Show MoreThis study is concerned with organizational learning and its impact on total quality management in the education sector. Organizational learning is a process that provides the educational sector with the ability to adapt and respond rapidly to developments and changes in a better way according to its main dimensions (Mental Models, Personal Mastery, Team Learning, Shared Vision, System Thinking) by adopting the philosophy of Total Quality Management (TQM) in accordance with its basic dimensions (leadership, customer satisfaction, participation of workers, continuous improvement, training and education). The main purpose of this study is to know (the impact of the Senge model of organizational learni
... Show Morehe aim of the research is to clarify the meanings and connotations of (Semitic), and to identify the peoples that fell under this name according to historical data, biblical texts and Qur’anic news. International sympathy on the one hand and on the other hand controlling the land of Palestine and giving them international legitimacy to grow their entity according to global support and sympathy with their alleged slogan (anti-Semitism), which revolves around the oppression of the Jews.
A Novel artificial neural network (ANN) model was constructed for calibration of a multivariate model for simultaneously quantitative analysis of the quaternary mixture composed of carbamazepine, carvedilol, diazepam, and furosemide. An eighty-four mixing formula where prepared and analyzed spectrophotometrically. Each analyte was formulated in six samples at different concentrations thus twentyfour samples for the four analytes were tested. A neural network of 10 hidden neurons was capable to fit data 100%. The suggested model can be applied for the quantitative chemical analysis for the proposed quaternary mixture.