The present work covers the analytical design process of three dimensional (3-D) hip joint prosthesis with numerical fatigue stress analysis. The analytical generation equations describing the different stem constructive parts (ball, neck, tour, cone, lower ball) have been presented to reform the stem model in a mathematical feature. The generated surface has been introduced to FE solver (Ansys version 11) in order to simulate the induced dynamic stresses and investigate the effect of every design parameter (ball radius, angle of neck, radius of neck, neck ratio, main tour radius, and outer tour radius) on the max. equivalent stresses for hip prosthesis made from titanium alloy. The dynamic loading case has been studied to a stumbling case. The load has been applied on the cap tip as a concentrated load distributed on the interface of ball and socket. The results show that the decreasing of max. Fatigue stress by (175) MPa could be obtained by increasing the outer tour radius from (10)mm to (15) mm and that will change the max. Fatigue zone location from the tour section to the neck. The ball radius and neck angle must be as lower as possible to decrease the fatigue stresses. The most dominate parameter to increase the safety factor is the radius of neck.
This paper presents a study for the influence of magnetohydrodynamic (MHD) on the oscillating flows of fractional Burgers’ fluid. The fractional calculus approach in the constitutive relationship model is introduced and a fractional Burgers’ model is built. The exact solution of the oscillating motions of a fractional Burgers’ fluid due to cosine and sine oscillations of an infinite flat plate are established with the help of integral transforms (Fourier sine and Laplace transforms). The expressions for the velocity field and the resulting shear stress that have been obtained, presented under integral and series form in terms of the generalized Mittag-Leffler function, satisfy all imposed initial and boundary conditions. Finall
... Show MoreA new spontaneous mutation (dh) is described for Culex quinquefasciatus Say. This
phenotype was observed in the second generation to cause complete coloration of the head
capsule and the siphon of the larvae. This character is mainly detectable in the larval stage
and slightly in the adult stage.
The reciprocal mass matting between mutants from F2 generation and normal wild type
sibs, revealed that the mode of inheritance can be controlled by an autosomal recessive
gene(s). This happened for both sexes with slightly variability in their expression. No
significant larval mortalities were found in all crosses.
Purpose A diagnosis of tuberculosis (TB) of the head and neck has been a dilemma for clinicians, because the clinical and pathologic features tend to mimic different pathologies. Our study aimed to identify the demographic, clinical, and pathologic features of head and neck TB to help healthcare providers in the early detection of the disease. Materials and Methods We performed a retrospective analysis using the medical archives at the pathology laboratory. Twenty-one patients with a clinical and pathologic diagnosis of head and neck TB were identified from 2010 to 2019. Results The age distribution was broad, with 28.5% of the patients younger than 15 years old. Seven patients had oral TB, with the most common sites affected the labial ves
... Show MoreIn this paper, a microcontroller-based electronic circuit have been designed and implemented for dental curing system using 8-bit MCS-51 microcontroller. Also a new control card is designed while considering advantages of microcontroller systems the time of curing was controlled automatically by preset values which were input from a push-button switch. An ignition based on PWM technique was used to reduce the high starting current needed for the halogen lamp. This paper and through the test result will show a good performance of the proposed system.
Recently, a great rise in the population and fast manufacturing processes were noticed. These processes release significant magnitudes of waste. These wastes occupied a notable ground region, generating big issues for the earth and the environment. To enhance the geotechnical properties of fine-grained soil, a sequence of research projects in the lab were conducted to analyze the impacts of adding sludge waste (SW). The tests were done on both natural and mixed soil with SW at various proportions (2%, 4%, 6%, 8%, and 10%) based on the dry mass of the soil used. The experiments conducted focused on consistency, compaction, and shear strength. With the addition of 10% of SW, the values of LL and PI decreased by 29.7% and 3
... Show MoreIn this study, the researcher aimed to define and measure the relevance and effect of the governmental organizations in complying with Iraqi Ministry of Transportation's requirements towards achieving the social responsibility, embodied in the ten commandments of the United Nations Findings displayed the availability of realization regarding organization managers towards social responsibility with their various capabilities and tendencies in relation with the representing entries of those Ten Commandments.The study showed the relation between the effectiveness of those organizations and dimensions of the ten commandments of social responsibility, with the existence of a significant effect for the said effectiveness on achiev
... Show MoreThe crude aqueous extract of menthespicata , the objective of this study was to investigate the effects of this extraction , on the histological changes of the ovares and levels of sex hormone , ( FSH , LH , Estradiol ) in albino female mice . the extract was given orally for( 45 ) days . fourty mature female mice were used in this study , the animals divided into four major groups . each group was include ten mice . the first three groups was given different concentration )) (21 , 14 , 7 %) . While the fourth group considered as control group which had been administrated tab water . For ( 45 ) days each group had been killed for hormonal assay in blood
... Show More