The study of these selected traces shows that what Imam Mardini did on Imam al-Zayla'i and enabled him to graduate the hadiths of the book (guidance and conclusions) as well as in choosing the novel closest to Murad the work and not as described by al-Zayla'i .... never deserves descriptions.

Background: overweight and obesity are the fifth leadingrisk for global deaths. At least 2.8 million adults die eachyear as a result of being overweight or obese. Numerousstudies show that weight loss, even if only 5-10%,significantly improves dyslipidemia, hypertension, diabetesmellitus, risk for osteoarthritis and its symptoms and risk forselected cancers.Objectives: is to evaluate the effect of diet and exerciseprogram on anthropometric and biochemical status of adultobese patients.Methods: descriptive study. 124 adult obese patientsattending Al Kindy obesity research and therapy unit duringDecember 2012 were included. Measurement of Wt, heightHt and WC performed and BMI was calculated. Laboratorytest analysis, on the fasting state, w

After the defeat of the military terrorist organization "ISIS" and the fall of the throne of its alleged state in the Iraqi city of Nineveh, in Syrian Baghouz, and the end of its control over the land, the Syrian camps, especially "Al-Hol" camp, emerge as an incubator for the ideology of the terrorist organization "ISIS" and a vital base for its consolidation and dissemination, which includes (68,000- 73,000) people. During the years following the military defeat of (ISIS), the camp witnesses the spread of extremist ideas widely at the hands of its residents, including the families of the organizations dead's, extremist detainees, and those who deal with it, taking advantage of the deterioration of the environmental, se

The present research aims to study the effect of friction stir welding (FSW) parameters on temperature distribution and tensile strength of aluminum 6061-T6. Rotational and traverse speeds used were (500,1000,1400 rpm) and (14,40,112 mm/min) respectively. Results of mechanical tests showed that using 500rpm and 14mm/min speed give the best strength. A three- dimensional fully coupled thermal-stress finite element model via ANSYS software has been developed. The Rate dependent Johnson-Cook relation was utilized for elasto-plastic work deformations. Heat-transfer is formulated using a moving heat source, and later used the transient temperature outputs from the thermal analysis to determine equivalent stresses in the welde

      Among Persian poets and literary works, Ferdowsi and Shahnameh have a distinctive and prominent place. Since the 5^th  C. AH , they took the interest of all Persian language and literature scholars and were one of the first books to be translated into different languages including Arabic by Al Fatih Bin Ali Bin Mohammed Al-Bandari in  the year of (620)AH  .Because it was completed in the early 7^th C. AH and in terms of antiquity, there is no older copy than  of Al-Bandari’s version  which holds great value in the analysis of  Shahnameh other different copies.

      To find out the how far analogy goes, the present paper makes a general comparisons of  Bijan and Manijeh in Shahnameh Fer

      An experimental and computational study is conducted to analyze the thermal performance of heat sinks and to pick up more profound information in this imperative field in the electronic cooling. One important approach to improve the heat transfer on the air-side of the heat exchanger is to adjust the fin geometry. Experiments are conducted to explore the impact of the changing of diverse operational and geometrical parameters on the heat sink thermal
performance. The working fluid used is air. Operational parameters includes: air Reynolds number (from 23597 to 3848.9) and heat flux (from 3954 to 38357 W/m
2 ). Conformational parameters includes: change the direction of air flow and the area of conduct

This paper deals with prediction the effect of soil remoulding (smear) on the ultimate bearing capacity of driven piles. The proposed method based on detecting the decrease in ultimate bearing capacity of the pile shaft (excluding the share of pile tip) after sliding downward. This was done via conducting an experimental study on three installed R.C piles in a sandy clayey silt soil. The piles were installed so that a gap space is left between its tip and the base of borehole. The piles were tested for ultimate bearing capacity
according to ASTM D1143 in three stages. Between each two stages the pile was jacked inside the borehole until a sliding of about 200mm is achieved to simulate the soil remoulding due to actual pile driving. T

BixSb2-xTe3 alloys with different ratios of Bi (x=0, 0.1, 0.3, 0.5, and 2) have been prepared, Thin films of these alloys were prepared using thermal evaporation method under vacuum of 10-5 Torr on glass substrates at room temperature with different deposition rate (0.16, 0.5, 0.83) nm/sec for thickness (100, 300, 500) respectively. The X–ray diffraction measurements for BixSb2-xTe3 bulk and thin films indicate the polycrystalline structure with a strong intensity of peak of plane (015) preferred orientation with additional peaks, (0015) and (1010 ) reflections planes, which is meaning that all films present a very good texture along the (015) plane axis at different intensities for each thin film for different thickness. AFM measureme

The present work aimed to study the SiO2μPs, and NPs effect on the biodegradability of St/PVA blends. The samples were prepared by casting method as PVA, St/PVA blends with different concentrations (30, 40, 50, and 60 %). FTIR test was carried out for the samples preparation. The results proved some changes which might be related to changing in crystallinity of St/PVA matrix as well as physical incorporation of SiO2 μPs, and NPs addition. The enzymatic test and water uptake results proved that increase in weight loss with increases of starch ratio. The lowest weight loss was PVA; the highest weight loss is 60% St/PVA whereas the lowest weight loss is 30%St/PVA for blends involved. SiO2μPs (753.7 nm), and NPs (263.1 nm) were added at d