In this study; a three-dimensional model was created to simulate groundwater in Al-Haydariyah area of the governorate of Al-Najaf. A solid model was created to utilize the cross sections of 25 boreholes in the research region, and it was made out of two layers: sand and clay. The steady-state calibration was employed in six observation wells to calibrate the model and establish the hydraulic conductivity, which was 17.49 m/d for sand and 1.042 m/d for clay, with a recharge rate of 0.00007 m/day. The wells in the research region were reallocated with a distance of 1500 m between each well, resulting in 140 wells evenly distributed throughout the study area and with a discharge of 5 l/s, and the scenarios were run for 1000 days to explore the impact of over-pumping on groundwater levels. The wells were operated at three different operating hours: 4, 8, and 12 h/d. According to the results, the largest water table decrease for each scenario was 0.35, 8.25, and 8.68 m, respectively. It was discovered that the first scenario, with an operating duration of 4 h/day and a discharge of 72 l/s, was the best scenario in which dry cells did not happen.
This research investigates the importance of social accounting and the auditor’s report. It basically checks if there is an impact of social accounting on the auditor’s report at the availability the INTOSAI standards No. (1700 and 1706). The study recruited 105 employees of the Federal Financial Supervision Office in Iraq. Data were collected using questionnaire. The questionnaire validity and reliability were checked to assure the truthfulness of the findings. The study found a positive correlation and a statistically significant effect between the accounting for social responsibility and the auditor’s report. It is necessarily recommended for the auditor and the bodies working in the Board of Supreme Audit to ensure the inclusio
... Show MoreThe study aimed to investigate the relationship between empowerment strategies and their impact on the success of enrichment work, it included the dimensions of empowerment strategies (power, knowledge, information, rewards), The dimensions of Job enrichment are (Skill variety, Task identity, Task significance, Autonomy, Feedback). The study was conducted at the headquarters of the Iraqi Oil Ministry in Baghdad and was based on a sample of the leadership of the ministry of managers consisting of 215 people. The data were collected using the questionnaire method based on scientific standards adopted in previous st
... Show MoreThe arrival of Russian President Vladimir Putin to power in the Russian Federation is an important factor in delineating a new approach to Russian policy towards regions that have great strategic importance affecting its national security. Therefore, NATO's progress eastward towards these regions prompts Russia to delineate a new strategy to confront this progress as well as preserving its control in the near neighboring regions represented by the countries of Eastern Europe, especially after the changes that occurred in those regions following the color revolutions that swept the region, such as the first application of this Russian policy in 2014, through the annexation of Crimea, and the latest military operations in Ukraine i
... Show MoreVarious Hall Effects have been successfully observed in samples of n-type indium antimonide with values for conductivity, energy gap, Hall mobility and Hall coefficient all agreeing with theory. A particular interest in developing a method for obtaining accurate values of carrier concentrations in semiconductor samples has been fulfilled with an experimental result of (1.6×1016 cm-3 ±10.7%) giving a percentage difference of (6.7%) to a quoted value of (1.5×1016cm-3) at (77K) using an (80mW C.W. CO2) laser beam at (10.6μm) to illuminate a similar sample of n-type indium antimonide, an "Optical" Hall effect has been observed. Although some doubt has been raised as to the validity of effect i.e. "thermal" rather than "Optical", values o
... Show MoreIn this study multi objective optimization is utilized to optimize a turning operation to reveal the appropriate level of process features. The goal of this work is to evaluate the optimal combination of cutting parameters like feed, spindle speed, inclination angle and workpiece material to have a best surface quality Taguchi technique L9 mixed orthogonal array, has been adopted to optimize the roughness of surface. Three rods of length around (200 mm) for the three metals are used for this work. Each rod is divided into three parts with 50 mm length. For brass the optimum parametric mix for minimum Ra is A1, B1 and C3, i.e., at tool inclination angle (5), feedrate of 0.01, spindle speed of 120
... Show MoreThis study delves into the properties of the associated act V over the monoid S of sinshT. It examines the relationship between faithful, finitely generated, and separated acts, as well as their connections to one-to-one and onto operators. Additionally, the correlation between acts over a monoid and modules over a ring is explored. Specifically, it is established that functions as an act over S if and only if functions as module, where T represents a nilpotent operator. Furthermore, it is proved that when T is onto operator and is finitely generated, is guaranteed to be finite-dimensional. Prove that for any bounded operator the following, is acting over S if and only if is a module where T is a nilpotent operator, is a
... Show More