The question about the existence of correlation between the parameters A and m of the Paris function is re-examined theoretically for brittle material such as alumina ceramic (Al2O3) with different grain size. Investigation about existence of the exponential function which fit a good approximation to the majority of experimental data of crack velocity versus stress intensity factor diagram. The rate theory of crack growth was applied for data of alumina ceramics samples in region I and making use of the values of the exponential function parameters the crack growth rate theory parameters were estimated.

                The characteristics of sulfur nanoparticles were studied by using atomic force microscope (AFM) analysis. The atomic force microscope (AFM) measurements showed that the average size of sulfur nanoparticles synthesized using thiosulfate sodium solution through the extract of cucurbita pepo extra was 93.62 nm. Protecting galvanized steel from corrosion in salt media was achieved by using sulfur nanoparticles in different temperatures. The obtained data of thermodynamic in the presence of sulfur nanoparticles referred to high value as compares to counterpart in the absence of sulfur nanoparticles, the high inhibition efficiency (%IE) and corrosion resistance were at high temperature, the corrosion rate or weig

In this research, the effect of electrode material on the parameters of the produced DBD plasma was investigated. First, a non-thermal plasma was created by applying a 15 kV AC voltage between two electrodes and using a glass plate as a dielectric barrier in the design Dielectric Barrier Discharge (DBD) plasma system. The obtained plasma spectrum was analyzed using optical emission spectroscopy to calculate plasma parameters by the Boltzmann plot method. Electrodes made of copper, aluminium, and stainless steel were employed in this research. Electron temperature ( ) for copper, aluminium, and stainless steel was found to be (1.398 eV), (1.093 eV) and (1.009 eV), respectively.

In light of increasing demand for energy consumption due to life complexity and its requirements, which reflected on architecture in type and size, Environmental challenges have emerged in the need to reduce emissions and power consumption within the construction sector. Which urged designers to improve the environmental performance of buildings by adopting new design approaches, Invest digital technology to facilitate design decision-making, in short time, effort and cost. Which doesn’t stop at the limits of acceptable efficiency, but extends to the level of (the highest performance), which doesn’t provide by traditional approaches that adopted by researchers and local institutions in their studies and architectural practices, limit

     This study aims to overcome the unexpected hydrocarbon non-potentiality detected in the upper Alam El-Bueib (I to IIIE) and justify the hydrocarbon accumulation within Alam El-Bueib (IIIG) at the Emry oil field, also, it is important to highlight the importance of fault seal analysis and the impact of Matruh canyon as a seal. Seismic interpretation and 3D structural framework are carried out using the fault-seal analysis technique for fault no.1 (F1). To assess the fault zone's capacity to be defined as either seal or leakage. Litho-facies juxtaposition diagram (Allan diagram) and Shale Gouge Ratio (SGR) were generated. It is concluded that the possible reason for the dry reservoir of the upper part of Alam El Bueib (Alam El Bue

The fouling depositions of crude oil stream were studied theoretically in a shell and tube heat exchanger to investigate the effect of depositions on the heat transfer process. The employed heat exchanger was with steam flowing in the inner tubes and crude oil in the shell at different velocities and bulk temperatures. It is assumed that fouling occurs only on the heated stream side (crude oil). The analysis was carried out for turbulent flow heat transfer conditions with wide range of Reynolds number, bulk temperature and time. Many previously proposed models for fouling resistance were employed to estimate a new model for fouling rate. It is found that the fouling rate and consequently the heat transfer coefficient were affected by Rey

The L. Cretaceous succession is the main reservoir rock in the south of Iraq. Although the upper Jurassic Sargelu Formation is the main source rock in this area; however, the organic-rich interval within the studied succession, is contribute in these huge accumulations of petroleum. The pyrolysis parameters of the succession; Sulaiy, yamama, Zubair, and Nahr Umr formations showed that the main kerogen type is type III and II with moderate to good HI, which they refer to gas and/or oil prone especially in Zubair, Nahr Umr, and Sulaiy formations. The quantity parameters indicate potential source intervals in respect to (TOC). The maturity parameters suggest the threshold and peak of petroleum generation, which Tmax values ranged around 430

Loss of drilling fluid in the Nasiriyah oil field can be considered as a big,
serious, and expensive problem at the same time, therefore accurate and integrated
program must be prepared before start drilling in layers that are likely to get loss
circulation. From the available data of well Ns-13, the area of loss was detected in
five layers, which are Dammam, Um- radoma, Tayarat, Shiranish and Hartha since
these layers contain natural cracks and high porosity represented by vugs.
Methods of prevention have been identified by specifying the minimum values
of drilling parameters to reduce hydrostatic pressure, thus reducing equivalent
density of drilling mud during the circulation, depths of casing shoes is
deter

      Rosemary is a well-known aromatic and medicinal plant used to treat various ailments. This study evaluated Rosmarinus officinalis essential oil for its phytochemical and antibacterial properties. The essential oil was analysed by using a gas chromatography-mass Spectrometry (GC-MS) that revealed the common chemicals containing verbenone 36.20% and 1,8-cineol (Eucalyptol) 12.14%. Extracted essential oils were tested for antibacterial activity against vancomycin intermediate Staphylococcus aureus (VISA), a strain of bacteria obtained locally from bacteremia patients. Three isolates were found to be VISA positive using the E-test (strips) and the population analysis profile method (PAP). VISA showed lower resist

The present study considers an influence of WS₂ nanoparticles lubricants on physical characteristics of wrought Aluminium alloys. It is investigated parameters-performance relationship via tribological pin-on-disc tests, the pin is made of Aluminium alloys and the disk is made of AISI.1045, and the humidity was 70%. Oils with WS₂ nanoparticles and without them reveal the loss rate of wear. In this study, the coefficient of friction (CoF) is reduced from 0.27 to 0.22 and the wear rate decreased from 0.128 x 10^-6 Nm^-1 to 0.107 x 10^-6 Nm^-1 at a load of 20 N. All worn surfaces were typically three types in wear mechanisms such as adhesive, abrasive, and oxidative wear. In addi