In drilling fluid program, selecting the drilling fluid that will reduce the lost time is the first objective, and will be economical regardless of its cost. The amount and type of solids in drilling fluid is the primary control of the rheological and filtration properties. Palygorskite clay (attapulgite) is an active solid that has the ability to reactive with its environment and form a gel structure within a fluid and due to its stability in the presence of brines and electrolytes this type of clay is preferred for use. The aim of this study is to improve properties of Iraqi palygorskite (PAL) by adding different chemical additives such as caustic soda NaOH and soda ash Na2CO3 with a different concentration in both fresh and salt water-based drilling fluid to satisfy the API specification and to compete with imported palygorskite. The palygorskite claystone of Late Cretaceous age is present in the Western Desert of Iraq within the Digma Formation. In this study, two areas in Western Desert palygorskite were obtained, Bahr Al-Najaf and Trefawi. The results of rheological properties showed that the performance of Bahr Al-Najaf PAL was more affected by caustic soda than Trefawi PAL. In contrast, Trefawi PAL performance was more affected with low concentrations of soda ash than Bahr Al-Najaf PAL in both fresh and salt water-based drilling fluid. Also, these additives lead to improve the value of pH in both fresh and salt drilling fluid that increases the ability of clay to be more dispersed in drilling fluid. Besides that, enhancement of drilling fluid prepared with Iraqi palygorskite stability to 85 and 80 in fresh and saltwater, respectively, was observed with soda ash additions.
This research was carried out to study the effect of plants on the wetted area for two soil types in Iraq and predict an equation to determine the wetted radius and depth for two different soil types cultivated with different types of plants, the wetting patterns for the soils were predicted at every thirty minute for a total irrigation time equal to 3 hr. Five defferent discharges of emitter and five initial volumetric soil moisture contents were used ranged between field capacity and wilting point were utilized to simulate the wetting patterns. The simulation of the water flow from a single point emitter was completed by utilized HYDRUS-2D/3D software, version 2.05. Two methods were used in developing equations to predict the domains o
... Show MoreThe current research aims to evaluate liquidity (as an independent variable) to improve the bank’s profitability (as a dependent variable ), by the bank’s ability to maximize its profits from its business results without excessive bank’s liquidity, so that may affect negatively affects the bank’s reputation and it’s dealers confidence in facing their financial obligations. and this may lead trying to come out among other recommendations including contributing to obtain, the bank’s ability to achieve liquidity balance to maximize its profits. This research has been applied to the sample induced intentionally by choosing three Iraqi private banks. The researcher used financial indicators to assess the bank’s liq
... Show MoreThe human resources are considered to be the main pillar of the organizations , economic development and the foundation of moving wheels of individual growth. This is considered as the basic tasks for any productive and economic activity . The investment of the human resources is the economic pillar of production , but the most important element of the production . This research tried to access the method of resource investment and to identify the problems and training as key element in establishment of E –government . A questionnaire document have been distributed to the workers at different levels in the colleges and institutes. The research concluded the necessity of job description , continuous training of the workers , usi
... Show MoreAn experimental study was performed to estimate the forced convection heat transfer performance and the pressure drop of a single layer graphene (GNPs) based DI-water nanofluid in a circular tube under a laminar flow and a uniform heat flux boundary conditions. The viscosity and thermal conductivity of nanofluid at weight concentrations of (0.1 to 1 wt%) were measured. The effects of the velocity of flow, heat flux and nanoparticle weight concentrations on the enhancement of the heat transfer are examined. The Nusselt number of the GNPs nanofluid was enhanced as the heat flux and the velocity of flow rate increased, and the maximum Nusselt number ratio (Nu nanofluid/ Nu base fluid) and thermal performance factor
... Show MoreThe objective of this study was to investigate the drought stress and plant density possibility on water productivity and grain yield of maize (Zea mays L.) (Planting Baghdad 3 synthetic varieties), Field experiment was conducted at Abu Ghraib Research Station (Baghdad) during spring and Autumn seasons of 2016 using a randomized complete block design arranged in split plot with three replications. Three irrigation treatment included: irrigation after depletion 50% of available water (T1), irrigation after depletion 75% of available water (T2) and irrigation after depletion 90% of available water (T3) in the main plots and three plant density which were: 1 seeds hill-1 (D1) giving a uniform plant density of 66666 plants ha-1 , 2 seeds hill1
... Show More|
Ferrite with the general formula CuLayFe2-yO4 (where y=0.02, 0.04, 0.06, 0.08 and 0.1), were prepared by standard ceramic technique. The main cubic spinel structure phase for all samples was confirmed by x-ray diffraction patterns with the appearance of small amount of secondary phases. The lattice parameter results were 8.285-8.348 Å. X-ray density increased with La addition and showed values between 5.5826 – 5.7461gm/cm3. The Atomic Force Microscopy (AFM) showed that the average grain size was decreasing with the increase in La concentration. The Hall coefficient was found to be positive. It de |
Quality function deployment tool is trying to improve health services through this study that will be applied in health sector environment , and be based on applying quality function deployment tool (QFD) TO preferable evaluation of main patients requirements in order to determine the technical requirements that need most attention across improving and developing health services .
Main requirements are determined to patients lying in the hospital (under research) which is (educational Baghdad \ medicine city office) in Baghdad, and other technical requirements through pers
... Show MorePurpose: This study's objective is to assess this relationship in the context of the banking industry in Iraq. The human resources management practices (HRMPs) Theoretical framework: in this study included recruiting and selection, training and development, performance appraisal, compensation and reward to testing relationship HRMPs. Design/methodology/approach: in this study; We analysed by used a quantitative approach, and 246 employees were selected as a sample and given a questionnaire. The SPSS software was used to examine the data that were obtained from the questionnaire. Findings: The study's findings revealed a variety of hypotheses and conclusions, including the following: competitive advantage (CA) is positively impacted by
... Show MoreThe wear behavior of alumina particulate reinforced A332 aluminium alloy composites produced by a stir casting process technique were investigated. A pin-on-disc type apparatus was employed for determining the sliding wear rate in composite samples at different grain size (1 µm, 12µm, 50 nm) and different weight percentage (0.05-0.1-0.5-1) wt% of alumina respectively. Mechanical properties characterization which strongly depends on microstructure properties of reinforcement revealed that the presence of ( nano , micro) alumina particulates lead to simultaneous increase in hardness, ultimate tensile stress (UTS), wear resistances. The results revealed that UTS, Hardness, Wear resistances increases with the increase in the percentage of
... Show More