The main objective of this study is to determine whether the use of He-Ne Laser (632.8 nm wavelength and power 0.5 mW) is an eligible and effective tool to kill or reduce the cell viability of Candida albicans isolated from complete upper dentures. Twenty one swabs were taken from the complete upper dentures. Only six swabs showed positive cultures for C. albicans. The isolate was divided into two groups, group I was not irradiated (control), and group II was irradiated by He-Ne Laser for different periods (10, 15, 20, and 30) min. After irradiation, the results showed a significant reduction in the viable cell count and colonies diameters especially at exposure periods 10 and 15 min. Although the low power He-Ne Laser was not eradicating t

This research deals with leverage and its impact on the profitability of Islamic banks in Iraq for the years (2015-2018), the research variables of leverage have been analyzed and measured as an independent variable, profitability as a dependent variable, and the research is based on a main hypothesis: there is a moral relationship of statistical significance. Between leverage and profitability at The Islamic Cooperation Bank for the period (2015-2018). The results of the research showed that there are moral (exorcist) relationships between the ratio of leverage and profitability indicators, as the higher the leverage ratio, the higher the profitability indicators. In addition, The Islamic Cooperation Bank has adopted a conservative poli

The present study aimed to investigate the effect of re-operations engineering business in continuous improvement, as the rapid development of service activities generally private and the great diversity in the goals of its operations and programs of the university and the service has led to the increasing importance of re-operations engineering business as well as continuous improvement so began to study the relationship between the re engineering and continuous improvement of university service, and applied study on a sample of professors from the faculties of administration, economics and law. Find and reach to several conclusions, notably that the preparation of the teaching staff training sessions on how to use modern teaching

The research deals with the subject of «ways to face rumors in the site of social networking Facebook», a research based on a doctoral thesis, as the research dealt with rumors in the most dangerous type of new media, which sites of social communication with the global community as spreading rumors of all kinds and afflicts everyone who has eyes on him Of the audience of these sites, and aims to identify the rumors on Facebook because it is one of the most popular sites in the world and the strategy of combating the rumors published by Facebook users in their personal pages and groups that organize them, as well as identify methods and methods that can be During which the face of the rumors in the said site and eliminate them t

The objective of the research is to identify the effect of the five-finger strategy on the holistic thinking of chemistry students in the second intermediate grade, where the sample consisted of 60 female students in a second classfrom one of the intermediate schools in Baghdad city, divided into two groups: control and experimental. The experimental design was based on the partial control; the scientific course was defined in the third and fourth chapters of the science book of the second intermediate grade.The two research tools were prepared: the attainment test with the scientific course and the holistic thinking scale paragraph (36) of multiple-choice pre- and posttest. The results showed a statistically significant difference between

An investigation was conducted for the determination of the effects of the forming conditions in the production of Gamma Alumina catalyst support on the crushing strength property. Eight variables were studied , they are ;binder content which is the sodium silicate , Solvent content which is the water, speed of mixing , time of mixing, drying temperature , drying time , calcinations temperature and the calcinations time
Design of the experiments was made by using the response Surface method in Minitab 15 software which supply us 90 experiments .
The results of this investigation show that the crushing strength for the dried Gamma alumina extrudate was affected by the drying temperature and the drying time only and there is no inter

The research problem stems from a chief question: “What is the nature of the responsibility that «Al-Sabah Al-Jadeed» and «Al-Mada» Newspapers have undertaken in promoting the values of citizenship and national belonging in the society? The research aims to achieve a number of goals, including: Determining the most prominent themes that were emphasized in the opinion articles in these two newspapers within the framework of the responsibility of promoting the values ​​of citizenship and national belonging in society, and revealing the most prominent topics that were discussed in opinion articles in the two sample newspapers regarding the promotion of the mentioned values. This research is a desc

Electrical Discharge Machining (EDM) is a widespread Nontraditional Machining (NTM) processes for manufacturing of a complicated geometry or very hard metals parts that are difficult to machine by traditional machining operations. Electrical discharge machining is a material removal (MR) process characterized by using electrical discharge erosion. This paper discusses the optimal parameters of EDM on high-speed steel (HSS) AISI M2 as a workpiece using copper and brass as an electrode. The input parameters used for experimental work are current (10, 24 and 42 A), pulse on time (100, 150 and 200 µs), and pulse off time (4, 12 and 25 µs) that have effect on the material removal rate (MRR), electrode wear rate (EWR) and wear ratio (WR). A

    In this work, an experimental study has been done to expect the heat characteristics and performance of the forced-convection from a heated horizontal rectangular fins array to air inside a rectangular cross-section duct. Three several configurations of rectangular fins array have been employed. One configuration without notches and perforations (solid) and two configurations with combination of rectangular-notches and circular-perforations for two various area removal percentages from fins namely 18% notches-9% perforations and 9% notches-18% perforations are utilized.  The rectangular fins dimensions and fins number are kept constant. The fins array is heated electrically from the base