Increased diseases and obesity currently due to increased production and excessive consumption of foods manufactured from non-food sweeteners without attention to the risk of consuming those additional high calories due to consuming these refreshing products such as juices and other various drinks, especially in the summer season by most segments of Iraqi society, especially workers, children and school students the aim of this study. Therefore, the study designed to replace sucrose with 0.03, 0.04 and 0.05% of each of the white stevia crystals and milled dry stevia leaves in the laboratory manufacture of juices and its effect on the general and sensory characteristics and the extent of their acceptability among the specialized residents. In addition to the control treatment, this was manufactured according to the specifications and concentration of the ingredients of juices manufactured by one of the locally famous juices manufacturing plants (Al-Shahir Factories) as a control treatment, with an added sucrose percentage of 8%. The results showed that the addition of stevia plant at 0.03 and 0.04% was most acceptable by sensory experts. The prepared orange juice was also analyzed for pH, titration acidity, dry matter, and density. The results also showed that by increasing the concentration of sweetener with the milled stevia plant, the pH of the mixture decreased and the acidity of the juice also increased. Whereas the juices with white stevia crystals were flavored with sweetness, clearer, more firm and acceptable by panelists.
Ultraviolet light radiation is applied to treat Plaque Psoriasis disease by targeted phototherapy. This is available through Narrowband-UVB light radiation devices peaked at wavelength 311 nm. Ten cases were chosen as a study group, 8 males aged 22-40 years old, and 2 females aged 25 and 32 years old who were exposed to ultraviolet light radiation. Their recovery or improvement was followed weekly. Different doses were used according to the severity of the lesion and as a trial for the outcome. The dose was given two times a week, starting with 200mJ/cm2, and subsequently increased by 100 or 200 mJ/cm2 reaching a maximum dose as tolerated by each individual patient. Improvement was observed after 4 – 6 weeks. The
... Show More
Electrospinning is a novel technique that can be used to produce highly porous fibers with highly tunable properties. In this research, this technique is adopted to prepare the electrospun nanofiber membrane for membrane distillation application. A custom-built electrospinning setup was made to prepare the nanofibers membrane. Polyvinylidene fluoride (PVDF) polymer was used in the electrospinning process due to its high hydrophobicity. Electrospun (PVDF) nanofibers were tested in direct contact membrane distillation (DCMD) process using 0.6 M sodium chloride as a feed solution. The resulting nanofiber membrane exhibited high performance in DCMD (i.e. relatively high water flux and high salt rejection). It has been found
... Show More
This research aims at studying each of the cold and hot thermal wavelengths affecting
Iraq for a minimum climatic course of 11 years beginning from 1992 till 2002. Three stations
were selected including the parts of Iraq surface: Mosul, Baghdad and Basrah.
The wave days were also connected with the related climatic elements represented by
the wind direction and speeds and the relative humidity. It was shown that Iraq is affected by
the rates of hot thermal wave lengths greatly compared to the rates of cold wavelengths. The
results suggested that the highest rate of hot and cold wavelengths recorded over Basra station
was (3.5) days for the cold and (5) days for the hot. While the lowest rates was at Mosul
station
Optical detector was manufactured Bashaddam thermal evaporation technique at room temperature under pressure rays studied characteristics of reactive Scout efficiency quantitative ratio of the signal and the ability equivalent to noise
(22)
(21)
(5)
(4)
The products of composites material are very sesetive to many variables, such as manufacturing process, additive materials, …. etc. Filler or additive plays a major role to determine the formation of the properties and behavior of the composites. In this study, polyethylene terephthalate-based compounds were produced and characterized. The work is concerned to prepare samples of Polyethylene terephthalate (PET) - zinc-ferrite (ZnFe2O4) with different addition ratio as zinc-ferrite (1, 2, 5, 10, 15 and 20) wt% obtained from mixing the solution with a hot pressing method applied under optimum conditions. The densities of the composites for all samples were calculated. Through the work the diffusion of zinc-ferrite i
... Show More
(14)
(12)
The irony pushes us to inquire about what is in the text of contradiction, irony, suspense, and other acts of paradox, as well as a departure from what is logical, or familiar, that attracts the attention of the addressee, and this is what drives us to introspect the text and interrogate it in order to get to know the intended product of the text or its real or metaphorical intent. On the other hand, the irony is more in the literary text than in the scientific texts. Therefore, critics add the word literature to it in their definition.
As it is represented by the paradox, we will seek to study the paradox of the title and the problematic that it may pose as the beginning of the text, and i
... Show More
Constitute a planning problem on the basis of personal experience and self-governance in the service organizations away from quantitative scientific method in planning an anchor and a platform, who made a recent research study, analysis and interpretation through scientific methodology adopted which formed its contents, The research aims to identify the true reality of production planning in service organizations, specifically in the Baghdad Hotel as a society to look, in order to assess the best strategy through the standard cost of the strategies of tracking and settlement to cope with developments on services demand changes, Search results confirmed that the settlement rates of production strategy is the best strategy in accordance wi
... Show More