Silicon nanowire arrays (SiNWs) are created utilizing the metal-assisted chemical etching method with an Ag metal as a catalyst and different etching time of 15, 30, and 60 minutes using n-Si (100). Physical properties such as structural, surface morphology, and optical properties of the prepared SiNWs are studied. The diameter of prepared SiNWs ranged from 20 to 280 nm, and the reflectance in the visible part of the wavelength spectrum was less than 1% for all prepared samples. The obtained energy gap of prepared SiNWs was around 2 eV, which is higher than the energy gap of bulk silicon. X-ray diffraction (XRD) has diffraction peaks at 68.70^o for all prepared samples. The heterojunction solar cell was fabricated based on the

The aim of this study to investigate the sexual harassment, prevention strategies, and the appropriate ways that tackle this phenomena. The current research consisted of four chapter; the first chapter gave a general introduction about the targeted topic followed by the problem of statement, the significance of study, study’s aims, and end with the limitations of study. The second section of chapter one referred to the common concepts of study. Third section addressed the previous studies that related to the current one. Chapter two concerned with the sexual violence against minors. It has four section; first section addressed number of concepts which related to sexual violence. The second section focused on the implications of sexual

Capillary pressure is a significant parameter in characterizing and modeling petroleum reservoirs. However, costly laboratory measurements may not be sufficiently available in some cases. The problem amplifies for carbonate reservoirs because relatively enormous capillary pressure curves are required for reservoir study due to heterogeneity. In this work, the laboratory measurements of capillary pressure and formation resistivity index were correlated as both parameters are functions of saturation. Forty-one core samples from an Iraqi carbonate reservoir were used to develop the correlation according to the hydraulic flow units concept. Flow zone indicator (FZI) and Pore Geometry and Structure (PGS) approaches were used to identify

Background: It is well known that mycotic antigens have an important
role in atopy and the induction of asthma. Now one of the important
subjects is the relation between respiratory bacterial and viral
infections in the inflammatory reactions accompanied with bronchial
asthma viruses Bacteria or their metabolites act as trigger for asthma
or increase it's intensity .
Objectives: To show the relation between asthma and some viral
infections serologically.
Methods: Direct ELISA test was employed to detect lgG specific for
Respiratory Syncytial virus (Rsv) parainfluenza virus type (p13) and
influenza virus in sera of (100) asthmatic patients of two age groups.
(10-17) and(18-50) years old. Serum samples from

There are no single materials which can withstand all the extreme operating conditions in modern technology.  Protection of the metals from hostile environments has therefore become a technical and economic necessity.  

In this work, for enhancing their wear-resistance, boride layers were deposited on the surface of low carbon steel by a pack cementation method at 850 °C for (2, 4, and 6) h using vacuum furnace. The boronizing process was achieved using different concentration of boron source (20, 25, and 30) % wt. into coating mixture to optimize the best conditions which ensure the higher properties with lower time. The coating was characteristic by X ray diffraction (XRD), and it is confirmed t

The research is divided into three chapters, the first of them to the research problem and its importance and its purpose and its limits, while the second chapter review of contemporary sculpture as a vision and concept, The third chapter came to view the most important results reached by the search.

In this study, the induced splined shaft teeth contact and bending stresses have been investigated numerically using finite element method(Ansys package version 11.0) with changing the most effecting design parameter,(pressure angle, teeth number, fillet radius and normal module), for internal and external splined shaft. Experimental work has been achieved using two dimensional photoelastic techniques to get the contact and bending stresses; the used material is Bakelite sheet type “PSM-4”.
The results of numerical stress analysis indicate that, the increasing of the pressure angle and fillet radius decrease the bending stress and increase the contact stress for both internal and external spline shaft teeth while the increasing of

The useful of remote sensing techniques in Environmental Engineering and another science is to save time, Coast and efforts, also to collect more accurate information under monitoring mechanism. In this research a number of statistical models were used for determining the best relationships between each water quality parameter and the mean reflectance values generated for different channels of radiometer operate simulated to the thematic Mappar satellite image. Among these models are the regression models which enable us to as certain and utilize a relation between a variable of interest. Called a dependent variable; and one or more independent variables

Islam was keen to get every man and woman a share of those benefits and wanted to marry and urged him. In order to unite efforts and articulates the arrow and clarifies the goal and I have a share in building a sober Islamic society, for all this and other research title is ((modern or planting and its impact on marital happiness)).