Background: Fiber-optic endoscopy is an important
investigation of the large intestine, whether or not the
radiologist (barium enema) has discovered a lesion in
the bowel. Colonoscopy affords a unique opportunity
to direct visualization of entire colonic mucosa. At
the same time, the physician can obtain biopsy specimens, remove polyps, and decompress volvuli.
Most experienced endoscopists and well prepared
patients can reach the cecum in over 90% of patients.
If colonoscopy is properly performed, it has a low
risk of complications, such as perforation and bleeding.
Methods: A total of 70 consecutive patients admitted
to Endoscopy department at Al-Kindy Teaching hospital from September- 2008 to July-2009. Bowel
preparation was achieved with Polyethylene glycol
lavage solution and 165 cm Pentax colonoscope
EC_3385FK 4.2 was used in all cases. All patients
were not sedated or given any other medication
Results:Seventy colonoscopies were performed in
this study. Forty of them were male and the rest were
female. The mean age was 42 years ranging from 4
years to 85 years. The most common indication for
colonoscopy was rectal bleeding (44%) Polyethylene
glycol lavage solution was used in all patients for
bowel preparation. All patients did not receive premedications. Complete colonoscopy examination was
done in (12.8%) of patients, the most common cause
of incomplete examination was poor bowel preparation (50%). No complications were reported.
Conclusions: Rectal bleeding was the most common
indication for colonoscopy. Poor bowel preparation
was the main cause of incomplete colonoscopy
The aim of this paper, study the effect of carbon nanotubes on the electrical properties of polyvinylchloride. Samples of polyvinylchloride carbon nanotubes composite prepared by using hot press technique. The weight percentages of carbon nanotubes are 0,5,10 and 20wt.%. Results showed that the D.C electrical conductivity increases with increasing of the weight percentages of carbon nanotubes. Also, the D.C electrical conductivity changed with increase temperature for different concentrations of carbon nanotubes. The activation energy of D.C electrical conductivity is decreased with increasing of carbon nanotubes concentration.
This study aimed to clarify the provisions of taking the mother for breastfeeding in Islamic jurisprudence, a comparative study between doctrines of jurisprudence. The ruling on forcing the mother to breastfeed, and the ruling on taking the mother for breastfeeding while she is in the infallibility of her husband, as well as in several reactionary divorces, and the ruling on breastfeeding in several divorced divorces. On breastfeeding in infallibility Face, as well as a several divorce reactionary, and worth the fare which is in several final divorces, and after the end of the marital relationship, has been proposed a number of recommendations, including it, is recommended to teach the provisions of the mother taking the taxi on breastfe
... Show More
(1)
(1)
The present work aims to investigate the aerodynamic characteristics of the winglet cant angle of Boeing 737-800 wing numerically and experimentally. The wing contain two swept angles 38.3o and 29.13o respectively, taper ratio 0.15 and aspect ratio 8.04. The wing involves three types of airfoils sections. Four cant angles for blended winglet have been considered (0o, 34o, 60o, 83.3o). The winglet has been analyzed to find the best cant angle for the wing without and with winglet. These models have been tested theoretically at Reynolds number of 2.06 x106 in order to study the winglet aerodynamic characteristics which consist of coefficient of Drag, coefficient of lift and Lift to drag ratio, pitching moment coefficient and bending moment co
... Show Moreسمير خلف فياض * و محسن طالب د.نوال عزت عبد اللطيف*, مجلة الهندسة والتكنولوجيا, 2010
The main objective of present work is to describe the feasibility of friction stir welding (FSW) for
joining of low carbon steel with dimensions (3 mm X 80 mm X 150 mm). A matrix (3×3) of welding
parameters (welding speed and tool rotational speed) was used to see influence of each parameter on
properties of welded joint .Series of (FSW) experiments were conducted using CNC milling machine
utilizing the wide range of rotational speed and transverse speed of the machine. Effect of welding
parameters on mechanical properties of weld joints were investigated using different mechanical tests
including (tensile and microhardness tests ). Micro structural change during (FSW) process was
studied and different welding zones
(25)
(19)
The present study was conducted on the Iraqi Pin-tailed Sandgrouse (Pterocles alchata) to study the lung's morphological description and histological structure. This study was used 5 samples of adult male sandgrouse bird. The birds were dissected. The lungs were removed from the coelomic cavity, cleaned to remove impurities, and photographed to describe their morphological features. The samples were fixed using formalin (10%) solution for 36-48 hours and then preserved in alcohol (70%) to prepare the microscopic slides. The results showed that the lung of the Iraqi sandgrouse bird is red in color, has a trapezoidal shape and has three surfaces (costal, visceral, and vertebral). The costal surface shows ribs impressions that extend f
... Show More