The DEM (Digital elevation model) means that the topography of the earth's surface (such as; Terrain relief and ocean floors), can be described mathematically by elevations as functions of three positions either in geographical coordinates, (Lat. Long. System) or in rectangular coordinates systems (X, Y, Z). Therefore, a DEM is an array number that represents spatial distributions of terrain characteristics. In this paper, the contour lines with different interval of high-resolution digital elevation model (1m) for AL-khamisah, The Qar Government was obtained. The altitudes ranging is between 1 m – 8.5 m, so characterized by varying heights within a small spatial region because it represents in multiple spots with flat surfaces.

Under cyclic loading, aluminum alloys exhibit less fatigue life than steel alloys of similar strength and this is considered as Achilles's heel of such alloys. A nanosecond fiber laser was used to apply high speed laser shock peening process on thin aluminum plates in order to enhance the fatigue life by introducing compressive residual stresses. The effect of three working parameters namely the pulse repetition rate (PRR), spot size (ω) and scanning speed (v) on limiting the fatigue failure was investigated. The optimum results, represented by the longer fatigue life, were at PRR of 22.5 kHz, ω of 0.04 mm and at both v's of 200 and 500 mm/sec. The research yielded significant results represented by a maximum percentage increase in the fa

The wear behavior of alumina particulate reinforced A332 aluminium alloy composites produced by a stir casting process technique were investigated. A pin-on-disc type apparatus was employed for determining the sliding wear rate in composite samples at different grain size (1 µm, 12µm, 50 nm) and different weight percentage (0.05-0.1-0.5-1) wt% of alumina respectively. Mechanical properties characterization which strongly depends on microstructure properties of reinforcement revealed that the presence of ( nano , micro) alumina particulates lead to simultaneous increase in hardness, ultimate tensile stress (UTS), wear resistances. The results revealed that UTS, Hardness, Wear resistances increases with the increase in the percentage of

In order to scrutinize the impact of the decoration of Sc upon the sensing performance of an XN nanotube (X = Al or Ga, and XNNT) in detecting sarin (SN), the density functionals M06-2X, τ-HCTHhyb, and B3LYP were utilized. The interaction of the pristine XNNT with SN was a physical adsorption with the sensing response (SR) of approximately 5.4. Decoration of the Sc metal into the surface of the AlN and GaN led to an increase in the adsorption energy of SN from −3.4 to −18.9, and −3.8 to −20.1 kcal/mol, respectively. Also, there was a significant increase in the corresponding SR to 38.0 and 100.5, the sensitivity of metal decorated XNNT (metal@XNNT) is increased. So, we found that Sc-decorating more increases the sensitivity of GaNN

The Yemen Kings and gaverners allered notable services to the pilgrims, who
were in their way to perform the pilgrimage to Mecca. Among them Al-Hysen Ibn
Salama (dead 384, Aih). The governer of Al- Zeadiea state, who concern about
pilgrimage route from its beginning at Hudrumot to its end at Mecca Al Makruma, the
distant was estimated by 60th days to pass the way he also eastablished asystem of
water “artesian wells” as long as the pilgrimage way also setting up large Mosqeses
and Marking out the way of the caravans of pilgrimage to save these caravans from
lossing the right way, he setting up under ground water chanal started from Arafat to
holy Mecca in order to ensure water supplies for the erea. This proje

The chemical composition of wastes of pressed grapes and found that the main components of wastes of pressed grapes, represented by the percentage of moisture was 6.47%, and the proportions are 3.71%. Either carbohydrates amounted to 85.77 %, either in fat models using petroleum ether Petroleum ether) was the increase of 0.27%. estimated the percentage of ash in the sampls was 3.78%, either fiber reached 69.47 %,, in addition to the test extracts towards the growth of seven types of bacteria, which included Bacillus subtilis, Bacillus cereus, Bacillus stearothermophilus, Escherishia coli, Staphylococcus aureus, Salmonella typhimurium and Pseudomonas fluorescens and yeast Candida albicans and Kluyveromyces marxianus, ( diffusion method ).

The study showed that Imam Said bin Jubair narrated in the transcriber and copied, which took most of the ink of the nation Ibn Abbas (may Allah be pleased with them), which amounted to fourteen novels.
The study also pointed out that the science of transcriber and copied is from the science of the Koran, which can only prove by the novel and the correct transmission of the Prophet Muhammad .
The study also showed that Imam Saeed bin Jubair, who says that it is permissible to copy in the Koran, contrary to what some scholars said that it is not permissible to copy.
The study also pointed to the possibility of copying and that the highest copies of the Koran Koran.

This paper aims to discuss and analyse the role and importance of implementing industrial Policy to promote industry and enhance economic development in developing countries. The paper discusses the economic justifications for using industrial policy as well as the criticisms leveled against it, for this purpose it analyses the ideas of two different approaches to industrial policy. The first held by the neo-liberals in the USA , who oppose the use of industrial policy and emphasise the role of the market in attaining economic development. The second, represented by many economists who support the use of industrial policy to promote industry and accelerate economic development, they justify their stand by pointing to the negative