Educational of the mind is a weapon to a different knowledges which
benefit in ife and developed the mind in many field and practice him in a
regular form in a right thinking and practice sense on exactly recognizing and
conception things which is senses and regulating the memory and providing
with benefit information which fit to minded of person,the present research
aimed at answering the following two questions:
1-Does the concept of mind differ with age?
2-Does the recognition on function of mind developed with development of
age?
The research population consisted of the children in the primary schools
of Baghdad/center,and the students of the Education for woman
college/Baghdad university for the age

Background: Levetiracetam is a member of the new antiepileptic drugs and has a broad spectrum effect, used as an adjunctive therapy in addition to monotherapy in the treatment of partial onset-seizures. The effect of levetiracetam on the development of embryo nervous system after maternal exposure during pregnancy has not been identified. Objective: to evaluate the effect of antiepileptic drug, levetiracetam (LEV) within its therapeutic dose 350mg/Kg body weight on albino female rat to clarify its effect on the developing cerebral cortex histologically. Material And Methods: Ten pregnant female rats were separated into two groups, control group and experimental group. They were obtained from the animal house of the high institute of inferti

Bac kground:: Septal deviation is one of the commonest anatomical deformities of the nasal skeleton, this deviation is usually accompanied by compensatory hypertrophy of the inferior turbinate on the concave side that will accentuate the severity of nasal obstruction.
Objectives: To evaluate the effect of septoplasty on the size of the inferior turbinate in patients with nasal septum deviation.
Methods: This is a prospective study of 25 patients attending the otolaryngological department at Al-Jirahat teaching hospital from September 2011 to November 2013, complaining mainly of nasal obstruction. Otolaryngological examination had shown nasal septum deviation. The cross sectional areas of inferior turbinates were measured with compu

The aim of this work is to study the factors that affect the welding joint of dissimilar metals. Austenitic stainless steel-type AISI (316L) with a thickness of (2mm) was welded to carbon steel (1mm) using an MIG spot welding.  The filler metal is a welding wire of the type E80S-G (according to AWS) is used with (1.2mm) diameter and CO₂ is used as shielding gas with flow rate (7L/min) for all times was used in this work.

        The results indicate that the increase of the welding current tends to increase the size of spot weld, and also increases the sheer force.  Whereas the sheer force increased inversely with the time of welding. Furthermore, the results indicate that i

The current research aims to test the impact of the strategy of merger (as an explanatory variable) in human resources management practices (as a response variable), and the importance of the subject being an important topic that mimics the Iraqi environment, where has seen many mergers that have not been addressed by former researchers in the field. In addition, the future prospects carry many mergers, and the problem of research was the lack of understanding among departments in how to manage the integration and deal with it, on the basis of scientific which reflected negatively on the practices of human resources management, and the research was based on two main hypotheses Six sub-hypotheses emerge to explore the correlation

Unlike fault diagnosis approaches based on the direct analysis of current and voltage signals, this paper proposes a diagnosis of induction motor faults through monitoring the variations in motor's parameters when it is subjected to an open circuit or short circuit faults. These parameters include stator and rotor resistances, self-inductances, and mutual inductance. The genetic algorithm and the trust-region method are used for the estimation process. Simulation results confirm the efficiency of both the genetic algorithm and the trust-region method in estimating the motor parameters; however, better performance in terms of estimation time is obtained when the trust-region method is adopted. The results also show the po

Flow of water under concrete dams generates uplift pressure under the dam, which may cause the dam to function improperly, in addition to the exit gradient that may cause piping if exceeded a safe value. Cutoff walls usually used to minimize the effect of flow under dams. It is required to
1)minimize the flow quantity to conserve water in the reservoir, it is also required to
2)minimize the uplift pressure under the dam to maintain stability of the dam, and it is required to

3) minimize the exit gradient to prevent quick condition to occur at the toe of the dam where piping may occur and may cause erosion of the soil. Varying the angle of cutoff walls affects its influence on the factors aforementioned that are required to

Expansive soil spreads in Iraq and some countries of the world. But there are many problems can be occurred to the structures that built on, so we must study the characteristics of these soils due to the  problems that may be caused to these structures which built on these kinds of soil and then study the methods of treatment. The present study focuses on improving  the geotechnical properties of expansive soils by treating it Metakaolin(M). Metakaolin (M) has never been used before as an improvement material  for stabilizing the expansive soil . Metakaolin  is a pozzolanic material. It’s obtained by calcination of kaolinite clay at temperatures from 700°C to 800°C. Kaolin chemical composition is

Increasing the variety of products that are being designed with sculptured surfaces, efficient machining of these surfaces has become more important in many manufacturing industries. The objective of the present work is the investigation of milling parameters for the sculptured surfacesthat effecting of surface roughness during machining of Al-alloy. The machining operation implemented on C-TEK CNC milling machine. The influence of the selected variables on the chosen characteristics have been accomplished using Taguchi design approach, also ANOVA had been utilized to evaluate the contributionsof each parameter on proc