This study investigates the application of hydraulic acid fracturing to enhance oil production in the Mishrif Formation of the Al-Fakkah oilfield due to declining flow rates and wellhead pressures resulting from asphaltene deposition and inadequate permeability. Implementing acid fracturing, an established technique for low-permeability carbonate reserves, was essential due to the inadequacy of prior solvent cleaning and acidizing efforts. The document outlines the protocols established prior to and following the treatment, emphasizing the importance of careful oversight to guarantee safety and efficacy. In the MiniFrac treatment, 150 barrels of #30 cross-linked gel were injected at 25 barrels per minute, followed by an overflush wi

Photonic crystal fiber interferometers are widely used for sensing applications. In this work, solid core-Photonic crystal fiber based on Mach-Zehnder modal interferometer for sensing refractive index was presented. The general structure of sensor applied by splicing short lengths of PCF in both sides with conventional single mode fiber (SMF-28). To apply modal interferometer theory; collapsing technique based on fusion splicing used to excite higher order modes (LP01 and LP11). Laser diode (1550 nm) has been used as a pump light source. Where a high sensitive optical spectrum analyzer (OSA) was used to monitor and record the transmitted. The experimental work shows that the interference spectrum of Photonic crystal fiber interferometer

Two simple methods for the determination of eugenol were developed. The first depends on the oxidative coupling of eugenol with p-amino-N,N-dimethylaniline (PADA) in the presence of K3[Fe(CN)6]. A linear regression calibration plot for eugenol was constructed at 600 nm, within a concentration range of 0.25-2.50 μg.mL–1 and a correlation coefficient (r) value of 0.9988. The limits of detection (LOD) and quantitation (LOQ) were 0.086 and 0.284 μg.mL–1, respectively. The second method is based on the dispersive liquid-liquid microextraction of the derivatized oxidative coupling product of eugenol with PADA. Under the optimized extraction procedure, the extracted colored product was determined spectrophotometrically at 618 nm. A l

ABSTRACT

In this research been to use some of the semi-parametric methods the based on the different function penalty as well as the methods proposed by the researcher  because these methods work to estimate and variable selection of significant at once for single index model including (SCAD-NPLS method , the first proposal SCAD-MAVE method , the second proposal  ALASSO-MAVE method ) .As it has been using a method simulation time to compare between the semi-parametric estimation method studied , and various simulation experiments to identify the best method based on the comparison criteria (mean squares error(MSE) and average  mean squares error (AMSE)).

And the use

The designer must find the optimum match between the object's technical and economic needs and the performance and production requirements of the various material options when choosing material for an engineering application. This study proposes an integrated (hybrid) strategy for selecting the optimal material for an engineering design depending on design requirements. The primary objective is to determine the best candidate material for the drone wings based on Ashby's performance indices and then rank the result using a grey relational technique with the entropy weight method. Aluminum alloys, titanium alloys, composites, and wood have been suggested as suitable materials for manufacturing drone wings. The requirement

In this paper, an Anti-Disturbance Compensator is suggested for the stabilization of a 6-DoF quadrotor Unmanned Aerial vehicle (UAV) system, namely, the Improved Active Disturbance Rejection Control (IADRC). The proposed Control Scheme rejects the disturbances subjected to this system and eliminates the effect of the uncertainties that the quadrotor system exhibits. The complete nonlinear mathematical model of the 6-DoF quadrotor UAV system has been used to design the four ADRCs units for the attitude and altitude stabilization. Stability analysis has been demonstrated for the Linear Extended State Observer (LESO) of each IADRC unit and the overall closed-loop system using Hurwitz stability criterion. A minimization to a

Abstract—Over the two past decades, the rapid integration of capital markets underlined the necessity for developing a single set of high quality international accounting standards. The growing acceptance of international accounting standards has given power for International Accounting Standards Board (IASB) to work and develop this project. Iraq is a country where its accounting practices have been influenced by different philosophies from outside and inside Iraq during its modern history. After the fall of Saddam Hussain international institutions have begun to play an important role in reshaping Iraq’s economy including its accounting for oil. This paper investigates the challenges and opportunities for Iraq in transitioning from it

المستخلص

يعد تقييم اداء العاملين احد اهم الركائز الاساسية التي يتوقف عليها نجاح أي منظمة تسعى بأن تتطور وتتميز بأنشطتها واداءها وبالأخص المنظمات التي لها خصوصية في عملها كالأجهزة الرقابية التي تعتمد في اداء انشطتها ومسؤولياتها على كفاءة مواردها البشرية, ومن هذا المنطلق يهدف هذا البحث الى تصميم انموذج ثلاثي المحاور (المؤهلات والقدرات، الاداء والانجاز، التعاون والالتزام الوظيفي) ثُماني المستويات

The research investigates the term innovation and its role in elaborating architectural practice based on diffusion. The complexity of the architectural field compared with other fields shows a problem in explaining how innovations in architecture diffuse as a thought and act in a certain context of practice. Therefore, the research aims to build an intellectual model that explains the way personal thoughts resembled by unique models introduced by creative and innovator designers diffuse in a certain pattern elaborate these models into a state of prevailing thought resembled by the movement in architecture. The research will apply its model to the more comprehensive movement in architecture, which is the modern movement,

يهدف البحث الى دراسة وتحليل الهندسة المتزامنة (CE) وتحسين التكلفة(CO)، واستعمال مخرجات الهندسة المتزامنة كمدخلات لتحسين التكلفة، وبيان دور الهندسة المتزامنة في تحسين جودة المنتوج، وتحقيق وفورات في وقت التصميم والتصنيع والتجميع وتخفيض التكاليف، فضلاً عن توظيف بعض النماذج لتحديد مقدار الوفورات في الوقت ومنها نموذج(Lexmark) ونموذج (Pert) لتحديد الوفورات في وقت التصميم وقت لتصنيع والتجميع.      ولتحقيق اهداف