Morphological and histoarchitecture aspects on the cerebrum of (barn owl) were made
to find outthe cerebrum size, design and the description of cerebral region components at the
light microscopic level by using Haematoxylin – Eosin and periodic acid schift (PAS)
stain methods. The result of the morphological aspects revealed that the cerebrum was large
and an obtuse triangle in shape, its surface had a slight furrow. Sagittal sections revealed
the location, arrangement and size of pallial and subpallial cerebral divisions. The result of
the microscopic examinations indicated that the large and massive hyperpallium (wulst) was
thick,hypertrophied wired, and multilaminate structure reflect their wider stereoscopic night
vision. The dorsolateral corticoid area (CDL) contained three different cell groups. The well
developed dorsal ventricular ridge (DVR) contained mesopalliumnidopallium and
arcopallium, contained voluminous nuclear heterogeneous neuron groups and pyramidal
cells. The higher density of the large pyramidal cells were found in the nidopallium (nest
pallium) that is surrounding the crescent shap lateral ventricle. The striatum had a striated
appearance due to its special histoarchitecture. The pallidum was the smallest and the
deepest among cerebral subdivision, it had a pale appearance
This paper describes the transport of Alkaloids through Rotating Discs Contactor (RDC) using n-decane as a liquid membrane. The transport of Pelletierine Alkaloid from a source phase through bulk liquid membrane to the receiving phase has been investigated. The general behaviour of Pertraction process indicates that% Extraction of pelletierine Alkaloid increased with increase in the number of stages and the agitation speed but high agitation speed was not favoured due to the increased risk of droplet formation during the operation. The pH of source and receiving phases were also investigated. The effect of organic solvent membrane on the extraction of Pelletierine was evaluated using ndecane, n-hexane and methyl cyclohexane. The results sho
... Show More
(23)
(18)
In this work, porous silicon gas sensor hs been fabricated on n-type crystalline silicon (c-Si) wafers of (100) orientation denoted by n-PS using electrochemical etching (ECE) process at etching time 10 min and etching current density 40 mA/cm2. Deposition of the catalyst (Cu) is done by immersing porous silicon (PS) layer in solution consists of 3ml from (Cu) chloride with 4ml (HF) and 12ml (ethanol) and 1 ml (H2O2). The structural, morphological and gas sensing behavior of porous silicon has been studied. The formation of nanostructured silicon is confirmed by using X-ray diffraction (XRD) measurement as well as it shows the formation of an oxide silicon layer due to chemical reaction. Atomic force microscope for PS illustrates that the p
... Show More
solation of candida spp. From cancer patients who suffered oral candidiasis due to immunodeficiency
(2)
<span lang="EN-US">Proper employment of Hybrid Wind/ PV system is often implemented near the load, and it is linked with the grid to study dynamic stability analysis. Generally, instability is because of sudden load demand variant and variant in renewable sources generation. As well as, weather variation creates several factors that affect the operation of the integrated hybrid system. So this paper introduces output result of a PV /wind via power electronic technique; DC chopper; that is linked to Iraqi power system to promote the facilitating achievement of Wind/ PV voltage. Moreover, PSS/E is used to study dynamic power stability for hybrid system which is attached to an effective region of Iraqi Network. The hybrid system
... Show More
(14)
(3)
The compressive residual stresses generated by shot peening, is increased in a direct proportional way with shot peening time (SPT). For each metal, there is an optimum shot peening time (O.S.T) which gives the optimum fatigue life. This paper experimentally studied to optimize shot peening time of aluminium alloy 6061-T651 as well as using of and analysis of variance (ANOVA).
Two types of fatigue test specimens’ configuration were used, one without notch (smooth) and the other with a notch radius (1,25mm), each type was shot peened at different time. The (O.S.T) was experimentally estimated to be 8 minutes reaching the surface stresses at maximum peak of -184.94 MPa.
A response surface methodology (RSM) is presen
... Show More
(1)
(8)
(6)
(1)