In this research the effect of grain size and effect of La2O3 doping on densification rate for the initial and intermediate stages of sintering were studied .The experimental results for α – cristobilite powder are modeled using ( L2-Regression ) technique in studying the effect of grain size and La2O3 doping using three particles size (6.12, 8.92, 13.6 ) µm, with undoped initial powder and with La2O3 doping . The mathematical simulation showes that the densification rates increase as the initial particles sizes decrease and vice versa. This shows that the densification depends directly on the initial compact density which reflects the contacts area between the particles . However the densification rates in the intermediate stages were enhanced compared with that of the initial stage .This is due to completion of neck growth that facilitates the mass transport between the grains ,and also, the presence of the massive grains due to the grain growth . Al so it is show that the doping enhances the densification rates in the intermediate stage due to that , the dopants act against the grain boundaries movement causing discourage closing of porosity and encourage escaping of voids enhances the densification rates .
According to the extraction procedure , Eucalyptus incrassata leave sample yielded 5% and 2% w/w(Based on dry leaves ) of the aqueous extract and essential oils respectively. Disk diffusion method was used to determine the antimicrobial activity of aqueous extract and essential oils of E . incrassata leaves against eight isolates of multidrug- resistant of Staphylococcus aureus ( S. aureus) . It was found that aqueous extract and essential oils have variable antimicrobial activity(the inhibition zone diameter ranged from 7 to 14 mm respectively ) , while essential oils showed more effect than aqueous extract . It was noticed that values of Minimal Inhibitory Concentration ( MIC ) for
... Show MoreThis paper presents an experimental and numerical study which was carried out to examine the influence of the size and the layout of the web openings on the load carrying capacity and the serviceability of reinforced concrete deep beams. Five full-scale simply supported reinforced concrete deep beams with two large web openings created in shear regions were tested up to failure. The shear span to overall depth ratio was (1.1). Square openings were located symmetrically relative to the midspan section either at the midpoint or at the interior boundaries of the shear span. Two different side dimensions for the square openings were considered, mainly, (200) mm and (230) mm. The strength results proved that the shear capacity of the dee
... Show More
(8)
This paper presents an experimental and numerical study which was carried out to examine the influence of the size and the layout of the web openings on the load carrying capacity and the serviceability of reinforced concrete deep beams. Five full-scale simply supported reinforced concrete deep beams with two large web openings created in shear regions were tested up to failure. The shear span to overall depth ratio was (1.1). Square openings were located symmetrically relative to the midspan section either at the midpoint or at the interior boundaries of the shear span. Two different side dimensions for the square openings were considered, mainly, (200) mm and (230) mm. The strength results proved that the shear capacity of the dee
... Show More
(9)
(8)
The master sintering concept is introduced as a unifying sintering model for the initial, intermediate and final stage of sintering. The master sintering curve is independent on the time-temperature trajectory due to account for its integral. The master sintering curve is constructed on a material parameter, which is the activation energy for sintering and other curve shaping parameters, which depends on the initial state of the powder. Literature data of sintering of TiO2 compacts with two initial packing densities of 55% and 69% of theoretical is utilized for the construction of the master sintering curves. The higher initial packing density compact shows higher densification rate, which is reflected by different set of shaping paramet
... Show MoreAn experimental study was conducted to evaluate the effect of AL-coholic extract alkaloid of Cordia myxa leafs in fourth larval stage of lesser grain borer Rhyzopertha dominica. Using alkaline extracts of 8%, the study has been shown clear effect increased in mortality rate for fourth larval stage 93.3% and degressed to 66.6% at 4% concentrate to 13.3% with control treatment .Ahigher percentage of pupal mortality 16.6% at 4% concentrate has been observed, while no natural emergence carried out at concentrates of 4.6% comparing with control treatment of 86.66%, at the same time percentage of deformation has been increased to 16.66% at 4% of extracts and degressed to 6.66% at 6% while no deformation have been shown with control treatment .
... Show MoreIn this research prepare membranes pure silicon carbide (SiC) as well as gas Alloy (ammonia) and using a laser was leaked membrane of glass flooring. To Drasesh optical properties of membranes prepared depending on the technique (Swanepoel) and Adhrt results obtained in general increased permeability pure silicon membranes
Thin films of Mn2O3 doped with Cu have been fabricated using the simplest and cheapest chemical spray pyrolysis technique onto a glass substrate heated up to 250 oC. Transmittance and absorptance spectra were studied in the wavelength range (300 -1100) nm. The average transmittance at low energy was about 60% and decrease with Cu doping, Optical constants like refractive index, extinction coefficient and dielectric constants (εr), (εi) are calculated and correlated with doping process.
Captopril is an angiotensin converting enzyme inhibitor (ACEI) used to treat hypertension,
congestive heart failure, and myocardial infraction.
The only dosage form available for captopril is the plain tablet in strength of 12.5,25,50 and 100mg
tablet.
This investigation is concerned with factors affecting the formulation of captopril as a plain
tablet dosage form of 50mg. Many trials were made to prepare satisfactory tablets for the drug by
using wet – granulation methods with various additives. It was found that poly vinyl pyrrolidone
(P.V.P.) as binder gave the most satisfactory tablets. At the same time a shorter disintegrantion time
and slower dissolution rate were obtained with the addition of starch
The study dealt with the effect o r the anticoagu l ant rodentici de Brcidi facom on the reproduction of male mus musculus trapped from d i ftcrent loculitieo of Uagltdad prov ince and ted with different doses (50
,75 ,100 mg) of pellets of this rodenticide. The results showed n significant decrease (p< 0.0 I ) in testicular weight and volume, epididymal ( head and tail) weight and numbers of different spermatogenic cells. The rodenticide caused a significant decrease in sperms concentration and a significant increase in dead and abnormal sperms in testes and epididymis.
This paper includes simulating an electron gun design to investigate the effect of the distance between the cathode and the Wehnelt cylinder bore on the quality of the ion beam emittance and to obtain the best distance of that geometrical factor. A study of a group of designs was conducted to find this distance. The SIMION8.0 program has been used to calculate the trajectories of the electrons with initial kinetic energy of (0.1 eV) and electron current of (1×10-12 A). The investigation also includes comparisons between the equipotential line trajectories for each design as well as the field distribution and the electron trajectories. The best emittance distance was concluded to be (3 mm).