Four novel Schiff bases SB1 to SB4 as new aromatic compound not hydrolysed under ordinary conditions were synthesized in this study by condensation reactions between2,4dinitrophenylhydrazine: firstly with 2,4,4`-trihydroxybenzophenone to give SB1, secondly with 4hydroxybenzophenone to give SB2, thirdly with 4-dimethylaminobenzaldhyde to give SB3 and fourthly with 4-aminobenzaldehyde to give SB4. The molecular structures of these aromatic Schiff bases obtained were identified and characterized based on melting points, elemental analysis(CHN), FT-IR and UV-Visible spectra. The electronic absorption spectra of Schiff bases obtained were studied in the solvents of ethanol, DMF, water, chloroform, carbon tetrachloride and cyclohexane. The recorded absorption bands in ethanol solvent were assigned to corresponding electronic transitions were discussed. The absorption bands at 291 to 411 nm obtained in electronic spectra of the synthesized new aromatic Schiff bases were assigned to (π→π*) transition which originates from substituted benzophenone or benzaldehyde rings and directed along of molecule in Schiff bases. These transitions are assumed to represent the intramolecular charge-transfer complexes bands in which the substituted two moieties of benzophenone and benzaldehyde rings are the charge donors and the substituted phenylhydrazine ring is the charge acceptor. Also, the effect of polar, non-polar solvents on the electronic transitions of charge-transfer bands have measured and discussed. The physical-spectroscopic parameters in molecular structural shapes of intra CT complexes molecules such as transition energies, molar extinction coefficients, molecular oscillate strength; transition molecular dipole moment and molecular resonance have been calculated and discussed.
(33)
(31)
In this study, an easy, low-cost, green, and environmentally
friendlier reagents have been used to prepare CdS QDs, in chemical
reaction method by mixed different ratio of CdO and sulfur in
paraffin liquid as solvent and oleic acid as the reacting media in
different concentration to get the optimum condition of the reaction
to formation CdS QDs. The results give an indication that the
behavior is at small concentration of 4ml of the oleic acid is best
concentration which give CdS QDs of small about to 9.23 nm with
nano fiber configuration.
Coupling reaction of 4-nitroaniline with 3-aminobenzoic acid provided the corresponding bidentate azo ligand. The prepared ligand was identified by Microelemental Analysis, 1H-NMR, FT-IR, and UV-Vis spectroscopic techniques. Treatment of the prepared ligand with Y(III) and La(III) metal ions in 1:3 M:L ratio in aqueous ethanol at optimum pH yielded a series of neutral complexes with the general formula of [M(L)3]. The prepared complexes were characterized by flame atomic absorption, Elemental Analysis (C, H, N), FT-IR, and UV-Vis spectroscopic methods, as well as conductivity measurements. The nature of the complexes formed were studied following the mole ratio and continuous variation methods; Beer's law obeyed over a concentration range o
... Show MoreMixedآ catechol- آ salicyladiminenate derivatives of antimony
|
(III) and tin (IV) of the general formula M(cate)L"]X, [where:M= Sb, X= آ 0; آ M=Sn, آ X= آ Cl; آ cate=catechol; آ n=l, آ L=aniline, آ n=2, آ L=mآ bromo-aniline, n=3, L=p-bromoaniline] were prepared by the reaction of equimolar amount of [(cate)MCln], [where n=l آ or 2] with Nآ arylsalicylaldimines HOC6H4CH=NC6Hs (HL1آ , HOC6H4CH= NC6H4
(3)
(3)
(2)
The influence of pre- shot peening and welding parameters on mechanical and metallurgical properties of dissimilar and similar aluminum alloys AA2024-T3 and AA6061-T6 joints using friction stir welding have been studied. In this work, numbers of plates were equipped from sheet alloys in dimensions (150*50*6) mm then some of them were exposed to shot peening process before friction stir welding using steel ball having diameter 1.25 mm for period of 15 minutes. FSW joints were manufactured from plates at three welding speeds (28, 40, 56 mm/min) and welding speed 40mm/min was chosen at a rotating speed of 1400 rpm for welding the dissimilar pre- shot plates. Tow joints were made at rotational speed of 1000 rpm and welding speed of 40m/min f
... Show More
(1)
The cost-effective removal of heavy metal ions represents a significant challenge in environmental science. In this study, we developed a straightforward and efficient reusable adsorbent by amalgamating chitosan and vermiculite (forming the CSVT composite), and comprehensively investigated its selective adsorption mechanism. Different techniques, such as Fourier-transform infrared spectroscopy (FTIR), zeta potential analysis, scanning electron microscopy (SEM), X-ray diffraction (XRD), and Brunauer, Emmett, Teller (BET) analysis were employed for this purpose. The prepared CSVT composite exhibited a larger surface area and higher mesoporosity increasing from 1.9 to 17.24 m2/g compared to pristine chitosan. The adsorption capabilities of the
... Show More
(30)
(31)
(7)
(8)
One technique used to prepare nanoparticles material is Pulsed Laser Ablation in Liquid (PLAL), Silver Oxide nanoparticles (AgO) were prepared by using this technique, where silver target was submerged in ultra-pure water (UPW) at room temperature after that Nd:Yag laser which characteristics by 1064 nm wavelength, Q-switched, and 6ns pulse duration was used to irradiated silver target. This preparation method was used to study the effects of laser irradiation on Nanoparticles synthesized by used varying laser pulse energy 1000 mJ, 500 mJ, and 100 mJ, with 500 pulses each time on the particle size. Nanoparticles are characterized using XRD, SEM, AFM, and UV-Visible spectroscopy. All the structural peaks determined by the XRD
... Show More
(3)
(1)