This work examines numerically the effects of particle size, particle thermal conductivity and inlet velocity of forced convection heat transfer in uniformly heated packed duct. Four packing material (Aluminum, Alumina, Glass and Nylon) with range of thermal conductivity (from200 W/m.K for Aluminum to 0.23 W/m.K for Nylon), four particle diameters (1, 3, 5 and 7 cm), inlet velocity ( 0.07, 0.19 and 0.32 m/s) and constant heat flux ( 1000, 2000 and 3000 W/ m ²) were investigated. Results showed that heat transfer (average Nusselt number Nu_av) increased with increasing packing conductivity; inlet velocity and heat flux, but decreased with increasing particle size.Also, Aluminum average Nusselt number is about (0.85,2.

This paper discussed the solution of an equivalent circuit of solar cell, where a single diode model is presented. The nonlinear equation of this model has suggested and analyzed an iterative algorithm, which work well for this equation with a suitable initial value for the iterative. The convergence of the proposed method is discussed. It is established that the algorithm has convergence of order six. The proposed algorithm is achieved with a various values of load resistance. Equation by means of equivalent circuit of a solar cell so all the determinations is achieved using Matlab in ambient temperature. The obtained results of this new method are given and the absolute errors is demonstrated.

Incremental sheet metal forming process is an advanced flexible manufacturing process to produce various 3D products without using dedicated tool as in conventional metal forming. There are a lot of process parameters that have effect on this process, studying the effect of some parameters on the strain distributions of the product over the length of deformation is the aim of this study.

In order to achieve this goal, three factors (tool forming shape, feed rate and incremental step size) are examined depending on three levels on the strain distributions over the wall of the product. Strain measurement was accomplished by using image processing technique using MATALB program. The significance of the control factors are explored u

Captopril is an angiotensin converting enzyme inhibitor (ACEI) used to treat hypertension,
congestive heart failure, and myocardial infraction.
The only dosage form available for captopril is the plain tablet in strength of 12.5,25,50 and 100mg
tablet.
This investigation is concerned with factors affecting the formulation of captopril as a plain
tablet dosage form of 50mg. Many trials were made to prepare satisfactory tablets for the drug by
using wet – granulation methods with various additives. It was found that poly vinyl pyrrolidone
(P.V.P.) as binder gave the most satisfactory tablets. At the same time a shorter disintegrantion time
and slower dissolution rate were obtained with the addition of starch

Abstract

This paper concerned with study the effect of a graphite micro powder mixed in the kerosene dielectric fluid during powder mixing electric discharge machining (PMEDM) of high carbon high chromium AISI D2 steel. The type of electrode (copper and graphite), the pulse current and the pulse-on time and mixing powder in kerosene dielectric fluid are taken as the process main input parameters. The material removal rate MRR, the tool wear ratio TWR and the work piece surface roughness (SR) are taken as output parameters to measure the process performance. The experiments are planned using response surface methodology (RSM) design procedure. Empirical models are developed for MRR, TWR and SR, using the analysis

The rapid development of information technology and its use in all areas has had a positive impact on all areas, and financial markets have had a share of this development through the use of an electronic trading system to settle transactions, enhance transparency and disclosure in all activities of these markets and revitalize their performance.

The reason for choosing this topic is that it is a very important topic for what modern technology addresses in trading operations in financial markets. It is worth noting that these innovations have eliminated the need for direct contact with people, but through the Internet and telephone networks, and the new technology has reduced the costs of building systems

The tax policy is an important tool of fiscal policy tools which is usedasits multiple tools the State seeks to achieve objectives, such as theachievement of economic development.The importance of the research comes from the importance ofeconomic development resulting from economic policies and prudent fiscaland appropriate to the economic situation of Iraq at the moment is the mostimportant tax policy that taxes one of the most important financial instruments.The research aims to clarify the role of tax policy in developing of theIraqi economy.In an effort to achieve the goals researchers tried to prove thehypothesis ((The tax policy and through multiple tools that seeks to contributeto the achievement of economic development in Iraq)).

Industry represents a cornerstone of the process of economic development and a measure of progress and contribute to increased prosperity and high standard of living.

The researcher analyzed the productivity indicators in industrial facilities large and small at several time periods ranging from 1970 to 2009, according to the economic situation that prevailed in each period.

    Different impact of periods under discussion, it made ​​Iraq the cash surpluses during the period 70-1980 then the effects of the war after 1980 and the economic blockade since 1990, and the subsequent events of the year