The process of granting loans by banks is the confidence they give to their customers, but this trust should not be a cornerstone in granting loans even if granted these loans on the basis of sound banking should involve risks that may be exposed to the bank because of the failure of the client to meet The bank's financial obligations to the bank due to the unexpected economic conditions affecting the customers, which makes them in a state of faltering, which weaken the ability of banks to provide loans, which are the most important sources of revenue and profits, so the problem of non-performing loans is one of the main problems facing most of the banks Which impede the functioning of its work and the reasons that led to the aggravation of the problem of banking failure and the lack of safety and the study of credit decisions in the case of granting loans and errors in the feasibility study and non-compliance with the procedures and controls of credit policies within the bank in addition to embezzlement and thefts exposed to the bank and the inefficiency of banking management and to avoid these The problem is that there is a need for careful study using scientific methods in terms of credit decisions and guarantees. This study varies according to the type of loan. In the case of long term loans, the risks are high. The volume of non-performing loans in the Rafidain Bank, the largest Iraqi banks and suffered large losses due to bad loans and inherited debt by the year 2003 and thereafter, which negatively affected the profits and reserves where the bank deduct part of its profits to meet non-refundable debt in the form of provision for doubtful debts despite the decline Its capital is due to the failure of the Rafidain Bank to comply with the instructions of the Central Bank of Iraq, especially with regard to the adequacy of capital and the guidelines for the classification of credit, which reflects the inefficiency of the bank's management in dealing with the problem of defaults
This work aims to provide a statistical analysis of metal removal during the Magnetic Abrasive Finishing process (MAF) and find out the mathematical model which describes the relationship between the process parameters and metal removal, also estimate the impact of the parameters on metal removal. In this study, the single point incremental forming was used to form the truncated cone made of low carbon steel (1008-AISI) based on the Z-level tool path. Then the finishing was accomplished using a magnetic abrasive process based on the Box-Behnken design of the experiment using Minitab 17 software was used to finish the surface of the formed truncated cone. The influences of different parameters (feed rate, machining step s
... Show MoreMansuriya Gas field is an elongated anticlinal structure aligned from NW to SE, about 25 km long and 5-6 km wide. Jeribe formation is considered the main reservoir where it contains condensate fluid and has a uniform thickness of about 60 m. The reservoir is significantly over-pressured, (TPOC, 2014).
This research is about well logs analysis, which involves the determination of Archie petrophysical parameters, water saturation, porosity, permeability and lithology. The interpretations and cross plots are done using Interactive Petrophysics (IP) V3.5 software.
The rock parameters (a, m and n) values are important in determining the water saturation where (m) can be calcul
... Show MoreA cantilever beam is made from composite material which is consist of (matrix: polyester) and (particles: Silicon-Carbide) with different volume fraction of particles. A force is applied at the free end of beam with different values. The experimental maximum deflection of beam which occurs at the point of the applied load is recorded. The deflection and slope of beam are analyzed by using FEM modeling. MATLAB paltform is built to assemble the equations, vector and matrix of FEM and solving the unknown variables (deflection and slope) at each node. Also ANSYS platform is used to modeling beam in finite element and solve the problem. The numerical methods are used to compare the results with the theoretical and experimental data. A good ag
... Show MoreA precise evaluation of caries excavation endpoint is essential in clinical and laboratory investigations. Caries invasion differentiates dentin into structurally altered layers. This study assessed these changes using Raman spectroscopy and Vickers microhardness. Ten permanent molars with occlusal and proximal carious lesions were assessed and compared at 130 points utilizing four Raman spectroscopic peaks: phosphate v1 at 960 cm−1, amide I (1650 cm−1), amide III (1235 cm−1) and the C-H bond of the pyrrolidine ring (1450 cm−1). The phosphate-to-amide I peak ratio and collagen integrity peak ratio (amide III: C-H bond) of carious zones were calculated and compared in both lesions. The former ratio was correlated to 130 Vicke
... Show MoreThe present study deals with the optimum design of self supporting steel communication towers. A special technique is used to represent the tower as an equivalent hollow tapered beam with variable cross section. Then this method is employed to find the best layout of the tower among prespecified configurations. The formulation of the problem is applied to four types of tower layout
with K and X brace, with equal and unequal panels. The objective function is the total weight of the tower. The variables are the base and the top dimensions, the number of panels for the tower and member's cross section areas. The formulations of design constraints are based on the requirements of EIA and ANSI codes for allowable stresses in the members