In the present research the flame retardancy to  buildings and industrial foundations which are manufacturing from advanced polymeric  composite material was increased by coating it with surface layer included flame retardant material.  A(3mm) thick antimony tetroxide was used as a coated layer to retard and prevent the flame spread to the coating surface of polyester resin (SIROPOL 8340-PI) reinforced with hybrid fibers as a woven roving (°45-°0) consist of carbon and kevlar (49) fibers, and exposed it to direct flame generated from gas torch at temperature of (2000ºC), at  different exposed distance (10,15,20mm)and study the rang of resistance for this layer and its ability to protec

Adsorption capacity of a waste biomass, date stones, for phenolic compounds such as phenol (Ph) and p-nitro phenol (PNPh) was investigated. The characteristics of such waste biomass were determined and found to have a surface area and iodine number of 495.71 m²/g and 475.88 mg/g, respectively. The effects of temperature, initial sorbate concentration, and contact time on the adsorption process were studied. Experimental equilibrium data for adsorption of Ph and PNPh on date stones were analyzed by the Langmuir, Freundlich and Sips isotherm models. The results show that the best fit was achieved with the Sips isotherm equation with maximum adsorption capacities of 147.09 and 179.62 mg/g for Ph and PNPh, respectively. The kinetic data wer

ABSTRACT Background: Polycystic ovary syndrome (PCOS) is one of the most common endocrine disorders affecting women in their reproductive age.It is characterized by anovulation or oligo-ovulation and hyperandrogensim.Androgen excess is the central defect in polycystic ovary syndrome. It is a complex disorder affects general health in addition to oral health.This study aimed to assess the gingival health status among a group of women with polycystic ovary syndrome as well as to estimate the levels of salivaryfree testosterone in unstimulated saliva in relation to gingival health condition. Materials and methods: Sixty two women with an age range 20-25 years old and with a body mass index range18.5-24.9 (normal weight) were included in this s

In this research tri metal oxides were fabricated by simple chemical spray pyrolysis technique from (Sn(NO₃)₂.20 H₂O, Zn(NO₃)₂.6 H₂O, Cd(NO₃)₂.4 H₂O) salts at concentration 0.1M with mixing weight ratio 50:50 were fabricated on silicon substrate n-type (111). (with & without the presence of grooves by the following diemensions (20μm width, 7.5μm depth) with thickness was about ( 0.1 ±0.05 µm) using water soluble as precursors at a substrate temperature 550 ºC±5, with spray distance (15 cm) and their gas sensing properties toward H₂S gas at different concentrations (10,50,100,500 ppmv) in air were investigated at room te

A new gravity and seismic survey along a profile length (70 Km) carried out at the area of exploration Block- 11 in Al- Najaf desert, southwest Iraq. The obtained gravity and seismic value compared with the previous available data that achieved by IPC and OEC for gravity and seismic data respectively. The difference between the new gravity profile and the old one is mainly in small anomaly not more than (14 %) that related to shallow depth levels and presents through power spectrum analysis. Previously, Ghulaissan-1 well which drilled in (1960) depend on a positive gravity and magnetic anomaly interpret, which is considered as an anticline structure in sub surface. It did not indicate any hydrocarbon shows after drilling, the integration

The influence of pre- shot peening and welding parameters on mechanical and metallurgical properties of dissimilar and similar aluminum alloys AA2024-T3 and AA6061-T6 joints using friction stir welding have been studied. In this work, numbers of plates were equipped from sheet alloys in dimensions (150*50*6) mm then some of them were exposed to shot peening process before friction stir welding using steel ball having diameter 1.25 mm for period of 15 minutes. FSW joints were manufactured from plates at three welding speeds (28, 40, 56 mm/min) and welding speed 40mm/min was chosen at a rotating speed of 1400 rpm for welding the dissimilar pre- shot plates. Tow joints were made at rotational speed of 1000 rpm and welding speed of 40m/min f