The fact of having Journalism being open to people from different orientations professions, working as journalists requiring protection just to spread corruption, is one of the biggest threats faced by journalism.

Journalists noticed the spread of unprincipled journalists with no journalistic ethics amongst them, they tried to protect their profession from these corrupt outsiders who might annihilate the mighty of journalism. The principles of the journalism profession known as journalistic ethics, are one the most important formulations of the law concluded by the journalists and those concerned by the the profession, they were then published in public in order to prove their professionalism, especially for those who don’t und

Praise be to God, prayer, and peace be upon the Messenger of Allah and his God and his companions. The field of the judiciary to prove or invalidate some cases in the field of proof of descent and attachment to the plaintiff or exile, and other legal and judicial issues, especially in this era where the spread of previously unknown evidence, such as DNA, which was discovered in 1953, and the genetic fingerprint discovered 1984, blood analysis and a Saliva, sweat, poetry, etc. in the field of forensic evidence, in forensic medicine or medical expertise, it can be used to identify the killer, or verify his identity, using all the evidence in the scene, such as a point of blood or sweat, and the like So, as well as to prove the lineage is u

In this work the effect of choosing tri-circular tube section had been addressed to minimize the end effector’s error, a comparison had been made between the tri-tube section and the traditional square cross section for a robot arm, the study shows that for the same weight of square section and tri-tube section the error may be reduced by about 33%.

A program had been built up by the use of MathCAD software to calculate the minimum weight of a square section robot arm that could with stand a given pay load and gives a minimum deflection. The second part of the program makes an optimization process for the dimension of the cross section and gives the dimensions of the tri-circular tube cross section that have the same weight of

Design and construction of video extractor circuit require an understanding of several parameters, which include: Selector circuit, extracting circuit which contains sampling signal and multiplexing. At each radar pulse, the video signal is fed to one of the selector. The fast filter has a pass –band from 190 Hz to 1800 Hz. These frequencies correspond to targets having radial velocities laying between and 10 Kph and 200 Kph.Slow filter: 60 Hz to 230 Hz for radial velocities laying between 3.5 and 13 Kph.The video- extractor is organized in four PCB CG (A-B-C-D) each one having 16 selector. The sampling signal (ADS) (1-2-3-4) control the 4-line-to-16-line decoders. 8 multiplexers of 8 inputs each, are required for the multiplexing of the

In this work the design and construction of optical pumping system was presented. The parameters of the pumping source to obtain discharge current density sufficient to shift the flash lamp spectrum towards uv portion of spectrum were measured.The current density was supplied to the flash lamp must be greater than 4000Amp./cm2 to obtain the spectral range wavelength lies between 0.2 and 0.35?m. The current density was obtained by a capacitor 50?F, at 7KV discharge voltage. The applied electrical energy to the flash lamp was more than 1200 J, and the current density was around 5000 Amp./cm2.The electrical parameters of the flash lamp were calculated. The impedance parameters(K0) from the voltage and the peak current pulse was measured in ran

In this work the design and construction of a flash photolysis pulsed HCl laser was presented. The parameters of the pumping source and discharge current density was obtained, which sufficient to shift the flash lamp spectrum towards uv portion of spectrum. The maximum pulse laser energy parameters was measured. Total pressure and ratio of active gases to optimized the output pulse energy were measured , where at 125 mbar of total pressure and 1:7:14 Cl2:H2: He ratio, the laser energy was measured to be 200 mJ at pumping four flash lamps energy in the order of 6400J .The resonator consists of copper a near hemispherical mirror with the radius of curvature 3m coated by gold and reflectivity 98%,the output coupler sapphire mirror of

The aim of this work is to develop an axi-symmetric two dimensional model based on a coupled simplified computational fluid dynamics (CFD) and Lagrangian method to predict the air flow patterns and drying of particles.  Then using this predictive tool to design more efficient spray dryers. The approach to this is to model what particles experience in the drying chamber with respect to air temperature and humidity. These histories can be obtained by combining the particles trajectories with the air temperature/humidity pattern in the spray dryer. Results are presented and discussed in terms of the air velocity, temperature, and humidity profiles within the chambers and compared for drying of a 42.5% solids solution in a spray chamber

The use of containers in transportation leads to the reduction in time and effort of the process of loading and unloading of goods as well as protecting the goods from damage and breakage and to reduce the financial costs.
. This development has led also to make changes in the sizes and capacity of ships, therefore changes in the ports must be taken place where they must be provided with an appropriate depth for such vessels, that means the increase in the depth of ports and the establishment of wide storage yards and to provide appropriate mechanisms for handling process.
In this study, the researcher has dealt with this type of transport business in Iraqi ports, namely:
1- Khur Al-Zubair port.
2- Um Qaser port.
In order

A 2D geological model for Mauddud Formation in the Badra oil field is built using Rockworks 16 software. Mauddud Formation produces oil from limestone units; it represents the main reservoir in the Badra oil field. Six wells (BD-1, BD-2, BD-4, BD-5, P-15, and P-19) are selected to build facies and petrophysical (Porosity and Water saturation) models. Wells data are taken from the core and cutting samples and studied through the microscopic. The petrophysical data (effective porosity and water saturation) are derived from computer processes interpretation results that are calculated by using Interactive Petrophysics software. The 2D models are built to illustrate the vertical and horizontal distribution of petrophysical properties between we