Objective: To evaluate the changes in the surface quality of irreversible hydrocolloid impression material
hydrogum following disinfection with 0.525% sodium hypochlorite, 0.2% Chlorehexidine Gluconate, and 4%
Povidone Iodine.
Methodology: Forty specimens of alginate impression materials hydrogum were fabricated according to the
ISO 1563 and were divided into four groups according to the method of solution dipping: group 1: Dip in
0.525% sodium hypochlorite, group 2: Dip in 0.2% chlorhexidine gluconate, Group 3: Dip in 4% Povidone Iodine,
Group 4: No treatment with any solution (control group). Then the specimens were poured in type II stone.
Surface detail was determined using a stainless steel block in accordance w

Fiscal policy is one of the important economic tools that affect economic development in general and human development in particular through its tools (public revenues, public expenditures, and the general budget).

It was hoped that the effects of fiscal policy during the study period (2004-2007) will positively reflect on human development indicators (health, education, income) by raising these indicators on the ground. After 2003, public revenues in Iraq increased due to increased revenues. However, despite this increase in public budgets, the actual impact on human development and its indicators was not equivalent to this increase in financial revenues. QR The value of the general budget allocations ha

The origin of occupations and trades producing goods and services necessary for the members of society
When people are designated to perform this task, in which case the state of change is included in the imposition of adequate labor rights, and may change from imposing sufficient to imposing the eye
Does the state have the right to compel "tradesmen and professions" to do their jobs?
Therefore, this research came to address the legitimacy of this from the perspective of the Islamic economy.

This work aims to investigate the tensile and compression strengths of heat- cured acrylic resin denture base material by adding styrene-butadiene (S- B) to polymethyl methacrylate (PMMA). The most well- known issue in prosthodontic practice is fracture of a denture base. All samples were a blend of (90%, 80%) PMMA and (10%, 20%) S- B powder melted in Oxolane (Tetra hydro furan). These samples were chopped down into specimens of dimensions 100x10x2.5mm to carry out the requirements of tensile tests. The compression strength test specimens were shaped into a cylinder with dimensions of 12.7mm in diameter and 20mm in length. The experimental results show a significant increase in both tensile and compression strengths when compared to cont

This paper represents an experimentalattempt to predict the influence of CO2-MAG welding variables on the shape factors of the weld joint geometry. Theinput variables were welding arc voltage, wire feeding speed and gas flow rate to investigate their effects on the shape factorsof the weld joint geometry in terms of weld joint dimensions (bead width, reinforcement height, and penetration). Design of experiment with response surface methodology technique was employed to buildmathematical models for shape factors in terms of the input welding variables. Thepredicted models were found quadratic type and statistically checked by ANOVA analysis for adequacy purpose. Also, numerical and graphical optimizations were carried out

 In this research the Cobalt Oxide (Co3O4) films are prepared by the method of chemical spray pyrolysis deposition at different thicknesses such that (250, 350, 450, and 550) ± 20 nm.      The optical measurement shows that the Co3O4 films have a direct energy gap, and they in general increase with the increase of the thickness. The optical constants are investigated and calculated such as absorption coefficient, refractive index, extinction coefficient and the dielectric constants for the wavelengths in the range (300-900) nm.     The electrical conductivity (σ) and the activation energies (Ea1, Ea2) have been investigated on (Co3O4) thin films as a function of thickness. The films

The electrical properties of polycrystalline cadmium telluride thin films of different thickness (200,300,400)nm deposited by thermal evaporation onto glass substrates at room temperature and treated at different annealing temperature (373, 423, 473) K are reported. Conductivity measurements have been showed that the conductivity increases from 5.69X10-5 to 0.0011, 0.0001 (?.cm)-1 when the film thickness and annealing temperature increase respectively. This increasing in ?d.c due to increasing the carrier concentration which result from the excess free Te in these films.

The aim of this research is to evaluate the effect of glucose and sodium chloride on biofilm formation by bacteria causing wound infection. For this purpose, 1% and 2% concentration of each of glucose and sodium chloride were used to test the biofilm formation potential of Staphylococcus aureus and Pseudomonas aeruginosa, which were the most common abundant bacteria that cause infection by biofilm. Each of the concentrations was kept in contact with the pathogenic bacteria for 24 hours. After the period of incubation, the concentration of 1% of glucose enhanced moderate biofilm formation capacity for (66% and 80%) on both bacteria respectively. The concentration of 2% glucose, on the other hand, led to a weak biofilm fo

The effect of SiO 2 ) Silica) on the dielectric and physical properties of Mnx-Ni1 -xFe2O4 ،، X=0.5 is studies. The samples are prepared by the conventional manufacturing
method. We found that the physical and dielectric properties of Mn-Ni ferrite change
considerably with the substituent samples .the variation of dielectric constant as a function of
frequency of ferrite system decrease with frequency increases and increase with the increase
the concentration of SiO 2 . It was found that the increase of SiO 2 concentration of all our
samples produce an increase in mass density and decrease with porosities

The neutron, proton, and matter densities of the ground state of the proton-rich ²³Al and ²⁷P exotic nuclei were analyzed using the binary cluster model (BCM). Two density parameterizations were used in BCM calculations namely; Gaussian (GS) and harmonic oscillator (HO) parameterizations. According to the calculated results, it found that the BCM gives a good description of the nuclear structure for above proton-rich exotic nuclei. The elastic form factors of the unstable ²³Al and ²⁷P exotic nuclei and those of their stable isotopes ²⁷Al and ³¹P are studied by the plane-wave Born approximation. The main difference between the elastic form factors of unstable nuclei and the