The Islamic Arts which include calligraphy and specifically the third line of the greatest
manifestation of Islamic civilization affair, and it was the mosques and mosques and holy
shrines scattered in the city of Baghdad, which had a deep impact in enhancing
communication
This means research study (third line aesthetics diversity of tactics in the architecture of
mosques) It is located in four seasons, which included the first chapter the research problem
represented by asking the following - :
-What are the methods of implementation of the third line in the architecture of mosques ?
And reflected the importance of research in it represents a serious attempt to investigate the
diversity in the organization design for linear configurations that promote communication
within and outside the mosques, mosques and holy sites located within the province of
Baghdad .
The objective of the study revealed the diversity of the methods implemented in the third line
Islamic mosques
The limits of the research has identified a third line configurations study varied within and
outside the corridors of mosques and mosques and holy sites of the era (2012 m -2013 m) and
their current, then seal chapter defines some of the terminology related to the subject matter ...
The second chapter goal of the theoretical framework and previous studies it was composed
of three sections define the first topic to address the third line study and aesthetic
characteristics .
The second topic was addressed by the researcher of the third line design spaces in the
building of mosques
The third chapter objective procedures for the research included the study population (42)
configuration in writing thuluth after excluding models repeated and similar and that Ataatuaq
with the objectives of the study or for other reasons, has chosen the researcher models sample
studied by the limited number (6) in a deliberate problem 20% of the Total community
researcher to study the original post after a group of experts with competence .
The samples were analyzed according to the sample analysis form that contributed to a lot of
experts .
The fourth chapter included the results of the study after an analysis and discussion of the
sample, which came the following - :
.1. Unity showed marked by the relationship with the other part, the part and the whole of
these relations is no doubt as to strengthen communication and raise satisfaction of sight at
the same time contribution in achieving the aesthetic diversity (sample models (
.2. Varied nature of the third line configurations implemented on the architectural elements in
the mosques and shrines between smooth and rough and Mabinhma diversity Mc contributes
largely to raise attention and enhance the aesthetic style within an area (sample models (
The conclusions that have chosen the most important researcher represented, including the
following - :
1.That each composition thuluth rhythm distinguishes whether free or regular or irregular,
uninteresting, or non-monotonic, or it may be a rhythm going because it expresses repeating
motor combines the unit and variable, one of the foundations of aesthetic overlay linear,
which has to be achieved in artwork
2.Calligrapher has maintained the consistency of parts of the characters with the college of the
Authority for the linear superposition of where (distance, height, and accuracy .(
And continue with the findings and conclusions of the recommendations and proposals
came then followed by a list of sources and supplements and then study researcher concluded
with a summary of research in the English language
(370)
(347)
The middle Cenomanian – early Turonian Mishrif Formation, a major carbonate reservoir unit in southern Iraq, was studied using cuttings and core samples and wireline logs (gamma‐ray, density and sonic) from 66 wells at 15 oilfields. Depositional facies ranging from deep marine to tidal flat were recorded. Microfacies interpretations together with wireline log interpretations show that the formation is composed of transgressive and regressive hemicycles. The regressive hemicycles are interpreted to indicate the progradation of rudist lithosomes (highstand systems tract deposits) towards distal basinal locations such as the Kumait, Luhais and Abu Amood oilfield areas. Transgressive hemicycles (transgressive systems tract deposits)
... Show More
(127)
(86)
The thermal and electrical performance of different designs of air based hybrid photovoltaic/thermal collectors is investigated experimentally and theoretically. The circulating air is used to cool PV panels and to collect the absorbed energy to improve their performance. Four different collectors have been designed, manufactured and instrumented namely; double PV panels without cooling (model I), single duct double pass collector (model II), double duct single pass (model III), and single duct single pass (model IV) . Each collector consists of: channel duct, glass cover, axial fan to circulate air and two PV panel in parallel connection. The temperature of the upper and
... Show More
(3)
Partial shading is one of the problems that affects the power production and the efficiency of photovoltaic module. A series of experimental work have been done of partial shading of monocrystalline PV module; 50W, Isc: 3.1A, Voc: 22V with 36 cells in series is achieved. Non-linear power output responses of the module are observed by applying various cases of partial shading (vertical and horizontal shading of solar cells in the module). Shading a single cell (corner cell) has the greatest impact on output energy. Horizontal shading or vertical shading reduced the power from 41W to 18W at constant solar radiation 1000W/m2 and steady state condition. Vertical blocking a column
... Show MoreOne of the most essential components of asphalt pavements is the filler. It serves two purposes. First, this fine-grained material (diameter less than 0.075 mm) improves the cohesiveness of aggregate with bitumen. Second, produce a dense mixture by filling the voids between the particles. Aluminum dross (AD), which is a by-product of aluminum re-melting, is formed all over the world. This material causes damage to humans and the environment; stockpiling AD in landfills is not the best solution. This research studies the possibility of replacing part of the conventional filler with aluminum dross. Three percent of dross was used, 10, 20, and 30% by filler weight. The MarshallMix design method was adopted to obtain the op
... Show More
(2)
(57)
(61)
Rheumatoid arthritis is a chronic, progressive, inflammatory autoimmune disease of unidentified etiology, associated with articular, extra-articular and systemic manifestation that require long-standing treatment. Taking patient’s beliefs about the prescribed medication in consideration had been shown to be an essential factor that affects adherence of the patient in whom having positive beliefs is an essential for better adherence. The purpose of the current study was to measure beliefs about medicines among a sample of Iraqi patients with Rheumatoid arthritis and to determine possible association between this belief and some patient-certain factors. This study is a cross-sectional study carried out on 250 already diagnosed rheumatoid
... Show More
(15)
(14)
In this research, the effect of adding two different types of reinforcing particles was investigated, which included: nano-zirconia (nano-ZrO2) particles and micro-lignin particles that were added with different volume fractions of 0.5%, 1%, 1.5% and 2% on the mechanical properties of polymer composite materials. They were prepared in this research, as a complete prosthesis and partial denture base materials was prepared, by using cold cure poly methyl methacrylate (PMMA) resin matrix. The composite specimens in this research consist of two groups according to the types of reinforced particles, were prepared by using casting methods, type (Hand Lay-Up) method. The first group consists of PMMA resin reinforced by (nano-ZrO
... Show More
(15)
The thermal and electrical performance of different designs of air based hybrid photovoltaic/thermal collectors is investigated experimentally and theoretically. The circulating air is used to cool PV panels and to collect the absorbed energy to improve their performance. Four different collectors have been designed, manufactured and instrumented namely; double PV panels without cooling (model I), single duct double pass collector (model II), double duct single pass (model III), and single duct single pass (model IV) . Each collector consists of: channel duct, glass cover, axial fan to circulate air and two PV panel in parallel connection. The temperature of the upper and lower surfaces of PV panels, air temper
... Show More
(3)