The Islamic Arts which include calligraphy and specifically the third line of the greatest
manifestation of Islamic civilization affair, and it was the mosques and mosques and holy
shrines scattered in the city of Baghdad, which had a deep impact in enhancing
communication
This means research study (third line aesthetics diversity of tactics in the architecture of
mosques) It is located in four seasons, which included the first chapter the research problem
represented by asking the following - :
-What are the methods of implementation of the third line in the architecture of mosques ?
And reflected the importance of research in it represents a serious attempt to investigate the
diversity in the organization design for linear configurations that promote communication
within and outside the mosques, mosques and holy sites located within the province of
Baghdad .
The objective of the study revealed the diversity of the methods implemented in the third line
Islamic mosques
The limits of the research has identified a third line configurations study varied within and
outside the corridors of mosques and mosques and holy sites of the era (2012 m -2013 m) and
their current, then seal chapter defines some of the terminology related to the subject matter ...
The second chapter goal of the theoretical framework and previous studies it was composed
of three sections define the first topic to address the third line study and aesthetic
characteristics .
The second topic was addressed by the researcher of the third line design spaces in the
building of mosques
The third chapter objective procedures for the research included the study population (42)
configuration in writing thuluth after excluding models repeated and similar and that Ataatuaq
with the objectives of the study or for other reasons, has chosen the researcher models sample
studied by the limited number (6) in a deliberate problem 20% of the Total community
researcher to study the original post after a group of experts with competence .
The samples were analyzed according to the sample analysis form that contributed to a lot of
experts .
The fourth chapter included the results of the study after an analysis and discussion of the
sample, which came the following - :
.1. Unity showed marked by the relationship with the other part, the part and the whole of
these relations is no doubt as to strengthen communication and raise satisfaction of sight at
the same time contribution in achieving the aesthetic diversity (sample models (
.2. Varied nature of the third line configurations implemented on the architectural elements in
the mosques and shrines between smooth and rough and Mabinhma diversity Mc contributes
largely to raise attention and enhance the aesthetic style within an area (sample models (
The conclusions that have chosen the most important researcher represented, including the
following - :
1.That each composition thuluth rhythm distinguishes whether free or regular or irregular,
uninteresting, or non-monotonic, or it may be a rhythm going because it expresses repeating
motor combines the unit and variable, one of the foundations of aesthetic overlay linear,
which has to be achieved in artwork
2.Calligrapher has maintained the consistency of parts of the characters with the college of the
Authority for the linear superposition of where (distance, height, and accuracy .(
And continue with the findings and conclusions of the recommendations and proposals
came then followed by a list of sources and supplements and then study researcher concluded
with a summary of research in the English language
(10)
The primary objective of this study is to manage price market items in the construction of walls for affordable structures with load-bearing hollow masonry units using the ACI 211.1 blend design with a slump range of 25-50 mm that follows the specification limits of IQS 1077. It was difficult to reach a suitable cement weight to minimum content (economic and environmental goal), so many trail mixtures were cast. A portion (10-20%) of the coarse aggregates was replaced with concrete, tile, and clay-brick waste. Finally, two curing methods were used: immersion under water as normal curing, and water spraying as it is closer to the field conditions. The recommendation in IQS 1077 to increase the curing period from 14 to 28 days was tak
... Show More
(6)
(7)
Copper selenide (Cu2Se) thin films were prepared by thermal evaporation at RT with thickness 500 nm. The heat-treating for (400 &500) K for the absorber layer has been investigated. This research includes, studying the structural properties of X-ray diffraction (XRD) that show the Cu2Se thin film (Cubic) and has a polycrystalline orientation prevalent (220). Moreover, studying the effect of annealing on their surface morphology properties by using Atomic Force Microscopy AFM. Optical properties were considered using the transmittance and absorbance spectra had been recorded when wavelength range (400 - 1000) nm in order to study the absorption coefficient and energy gap. It was found that these films had allowed direct transitio
... Show More
(12)
(14)
Background: Recurrent laryngeal nerve injury is
an important post-thyroidectomy complication for
which different modalities of treatment were
practiced to lower its incidence.
Objectives: To estimate the incidence of
recurrent laryngeal nerve injury in thyroid surgeries
in relation to type of surgery, type of gland diseases
& nerve identification.
Methods: Different types of goiters prepared
preoperatively by indirect laryngoscopy, operated
upon with different types of surgeries, postoperative
direct laryngoscopy by the anaesthetist were done
and indirect laryngoscopy done as needed.
Results: Of of 200 patients, the overall incidence
of recurrent laryngeal nerve injury was 9
Patients (4.5%
(2)
Applications of nonlinear, time variant, and variable parameters represent a big challenge in a conventional control systems, the control strategy of the fuzzy systems may be represents a simple, a robust and an intelligent solution for such applications.
This paper presents a design of fuzzy control system that consists of three sub controllers; a fuzzy temperature controller (FC_T), a fuzzy humidity controller (FC_H) and a ventilation control system; to control the complicate environment of the greenhouse (GH) using a proposed multi-choice control system approach. However, to reduce the cost of the crop production in the GH, the first choice is using the ventilation system to control the temperature and humidit
... Show MoreIn all process industries, the process variables like flow, pressure, level, concentration
and temperature are the main parameters that need to be controlled in both set point
and load changes.
A control system of propylene glycol production in a non isothermal (CSTR) was
developed in this work where the dynamic and control system based on basic mass
and energy balance were carried out.
Inlet concentration and temperature are the two disturbances, while the inlet
volumetric flow rate and the coolant temperature are the two manipulations. The
objective is to maintain constant temperature and concentration within the CSTR.
A dynamic model for non isothermal CSTR is described by a first order plus dead
time (FO
The aim of this work is to study the factors that affect the welding joint of dissimilar metals. Austenitic stainless steel-type AISI (316L) with a thickness of (2mm) was welded to carbon steel (1mm) using an MIG spot welding. The filler metal is a welding wire of the type E80S-G (according to AWS) is used with (1.2mm) diameter and CO2 is used as shielding gas with flow rate (7L/min) for all times was used in this work.
The results indicate that the increase of the welding current tends to increase the size of spot weld, and also increases the sheer force. Whereas the sheer force increased inversely with the time of welding. Furthermore, the results indicate that i
... Show MoreEconomic units can benefit from the cleaner production strategy, which aims to reduce the environmental impact of economic activities while improving efficiency and profitability. Accordingly, the aim of the research was to clarify the knowledge foundations of cleaner production costs and to indicate their role in reducing the costs of poor quality (the costs of failure). A set of conclusions has been reached, the most important of which is that cleaner production has achieved a reduction in the costs of external failure, represented by the costs of guarantee, by an amount of 12,339,000 dinars. Contributes to reducing the costs of failure, and based on the conclusions, a set of recommendations were presented, the most important of w
... Show More
(2)