The Islamic Arts which include calligraphy and specifically the third line of the greatest
manifestation of Islamic civilization affair, and it was the mosques and mosques and holy
shrines scattered in the city of Baghdad, which had a deep impact in enhancing
communication
This means research study (third line aesthetics diversity of tactics in the architecture of
mosques) It is located in four seasons, which included the first chapter the research problem
represented by asking the following - :
-What are the methods of implementation of the third line in the architecture of mosques ?
And reflected the importance of research in it represents a serious attempt to investigate the
diversity in the organization design for linear configurations that promote communication
within and outside the mosques, mosques and holy sites located within the province of
Baghdad .
The objective of the study revealed the diversity of the methods implemented in the third line
Islamic mosques
The limits of the research has identified a third line configurations study varied within and
outside the corridors of mosques and mosques and holy sites of the era (2012 m -2013 m) and
their current, then seal chapter defines some of the terminology related to the subject matter ...
The second chapter goal of the theoretical framework and previous studies it was composed
of three sections define the first topic to address the third line study and aesthetic
characteristics .
The second topic was addressed by the researcher of the third line design spaces in the
building of mosques
The third chapter objective procedures for the research included the study population (42)
configuration in writing thuluth after excluding models repeated and similar and that Ataatuaq
with the objectives of the study or for other reasons, has chosen the researcher models sample
studied by the limited number (6) in a deliberate problem 20% of the Total community
researcher to study the original post after a group of experts with competence .
The samples were analyzed according to the sample analysis form that contributed to a lot of
experts .
The fourth chapter included the results of the study after an analysis and discussion of the
sample, which came the following - :
.1. Unity showed marked by the relationship with the other part, the part and the whole of
these relations is no doubt as to strengthen communication and raise satisfaction of sight at
the same time contribution in achieving the aesthetic diversity (sample models (
.2. Varied nature of the third line configurations implemented on the architectural elements in
the mosques and shrines between smooth and rough and Mabinhma diversity Mc contributes
largely to raise attention and enhance the aesthetic style within an area (sample models (
The conclusions that have chosen the most important researcher represented, including the
following - :
1.That each composition thuluth rhythm distinguishes whether free or regular or irregular,
uninteresting, or non-monotonic, or it may be a rhythm going because it expresses repeating
motor combines the unit and variable, one of the foundations of aesthetic overlay linear,
which has to be achieved in artwork
2.Calligrapher has maintained the consistency of parts of the characters with the college of the
Authority for the linear superposition of where (distance, height, and accuracy .(
And continue with the findings and conclusions of the recommendations and proposals
came then followed by a list of sources and supplements and then study researcher concluded
with a summary of research in the English language
An experimental investigation has been carried out for zinc-nickel (Zn-Ni) electro-deposition using the constant applied current technique. Weight difference approach method was used to determine the cathode current efficiency and deposit thickness. Also, the influence effect of current density on the deposition process, solderability, and porosity of the plating layer in microelectronic applications were examined. The bath temperature effect on nickel composition and the form of the contract was studied using Scanning Electron Microscope (SEM). Moreover, elemental nature of the deposition was analyzed by Energy Dispersive X-Ray (EDX).
It has been found that the best bath temperature
... Show MoreA novel mixed natural coagulant has been developed to remove sewage pollutants and heavy metals from Qanat- al- Jayesh by using low cost adsorbent natural materials. In these materials, significant interaction contains Arabic gum mixed with extracted silica from rice husk ash (natural coagulants) by the Batch device approach, using two variables, pH values ranging from 5-8 and contact times between 0.25-5 hrs. All wastewater samples were collected after treatment by adsorbents and examined for determination of residual heavy metal concentrations: Pb, Ni, Zn and Cu by atomic absorption spectroscopy (AAS), turbidity, pH, total dissolved salts (TDS), electrical conductivity (EC) and total salinity (TS). The results obtained indicate Th
... Show More
(2)
(2)
The design, construction and investigation of experimental study of two compound parabolic concentrators (CPCs) with tubular absorber have been presented. The performance of CPCs have been evaluated by using outdoor experimental measurements including the instantaneous thermal efficiency. The two CPCs are tested instantly by holding them on a common structure. Many tests are conducted in the present work by truncating one of them in three different levels. For each truncation the acceptance half angle (θc) was changed. Geometrically, the acceptance half angle for standard CPC is (26o). For the truncation levels for the other CPC 1, 2 and 3 the acceptance half angle were 20o, 26o and 5
... Show MoreThe present work aimed to study the SiO2μPs, and NPs effect on the biodegradability of St/PVA blends. The samples were prepared by casting method as PVA, St/PVA blends with different concentrations (30, 40, 50, and 60 %). FTIR test was carried out for the samples preparation. The results proved some changes which might be related to changing in crystallinity of St/PVA matrix as well as physical incorporation of SiO2 μPs, and NPs addition. The enzymatic test and water uptake results proved that increase in weight loss with increases of starch ratio. The lowest weight loss was PVA; the highest weight loss is 60% St/PVA whereas the lowest weight loss is 30%St/PVA for blends involved. SiO2μPs (753.7 nm), and NPs (263.1 nm) were added at d
... Show More
In this study porcelain was prepared by using composition consisting of raw materials with in following fractions , 50% kaolin , 25% feldspar, and 25% silica( SiO2) tested by XRay diffraction (XRD) method .Study the effect additives at different concentration from zirconia (ZrO2) (2,5,10,15,20) Wt% on some physical properties of porcelain, the sample is prepared by the conventional manufacturing method , It is found that some physical properties of porcelain changes considerably with the substituent sample, It was found that the increase of zrconia (ZrO2) additive of all our sample produce. Increasing in dielectric constant and bulk density and decreasing with open porosity and dielectric loss tangent
(10)
(5)
Objectives: The aim of the study was, to assess the nurse's role regarding cardiovascular drug
administration in Erbil city.
Methodology: A descriptive survey was conducted in Hawler teaching and Rizgari teaching Hospitals. The
number of samples is 50 nurses; the period of the study was started from 15th of November 2008 up to
the end of March 2009. A questionnaire was developed by investigators based on extensive review of
available studies and literatures. Data were collected through application of observational check list
consist of two part, part one was demographic sheet and part two about nurse’s responsibility regarding
medication administration which include (before, during, after drug administration). Data
This paper deals with prediction the effect of soil remoulding (smear) on the ultimate bearing capacity of driven piles. The proposed method based on detecting the decrease in ultimate bearing capacity of the pile shaft (excluding the share of pile tip) after sliding downward. This was done via conducting an experimental study on three installed R.C piles in a sandy clayey silt soil. The piles were installed so that a gap space is left between its tip and the base of borehole. The piles were tested for ultimate bearing capacity
according to ASTM D1143 in three stages. Between each two stages the pile was jacked inside the borehole until a sliding of about 200mm is achieved to simulate the soil remoulding due to actual pile driving. T
(1)