The (CTLA-4) encodes of the T cell receptor involved in the control of T cell
proliferation and mediates T cell apoptosis. The contribution of CTLA-4 gene
variants to type 1 diabetes has been analyzed in several ethnic groups. In this study,
the association of CTLA-4 +49 A/G polymorphism with type 1 diabetes was
investigated in Egyptian patients. Sixty type 1 diabetic patients (25 males and 35
females) and 60 healthy individuals (33 males and 27 females) subjects formed the
studied populations. CTLA-4 A/G polymorphism at position 49 in exon 1 was
identified using allele specific methods. Patient numbers with A/G, A/A and G/G
genotypes were 45 (75.0 %), 6 (10.0 %) and 9 (15.0%) while in healthy controls,
these w

An experimental and theoretical works were carried out to model the wire condenser in the domestic refrigerator by calculating the heat transfer coefficient and pressure drop and finding the optimum performance. The two methods were used for calculation, zone method, and an integral method. The work was conducted by using two wire condensers with equal length but different in tube diameters, two refrigerants, R-134a and R-600a, and two different compressors matching the refrigerant type. In the experimental work, the optimum charge was found for the refrigerator according to ASHRAE recommendation. Then, the tests were done at 32˚C ambient temperature in a closed room with dimension (2m*2m*3m). The results showed that th

Abstract: Urinary Tract Infections (UTIs) are the most common bacterial infection in humans and a major cause of morbidity and they are the most common cause of hospital visits worldwide. Proper knowledge in identifying factors associated with urinary tract infection may allow the intervention to easily control of the disease in a timely manner. Therefore, the purpose of the study is determining the prevalence of UTI, diagnosis of causative bacterial agents and identifying the factors associated to the urinary tract infection among patients attending Medical City Hospital in Baghdad, Iraq. A total of 237, morning mid-stream urine samples were collected aseptically and the samples were diagnosed according to the standard methods. I

A chemometric method, partial least squares regression (PLS) was applied for the simultaneous determination of piroxicam (PIR), naproxen (NAP), diclofenac sodium (DIC), and mefenamic acid (MEF) in synthetic mixtures and commercial formulations. The proposed method is based on the use of spectrophotometric data coupled with PLS multivariate calibration. The Spectra of drugs were recorded at concentrations in the linear range of 1.0 - 10 μg mL-1 for NAP and from 1.0 - 20 μg mL-1 for PIR, DIC, and MEF. 34 sets of mixtures were used for calibration and 10 sets of mixtures were used for validation in the wavelength range of 200 to 400 nm with the wavelength interval λ = 1 nm in methanol. This method has been used successfully to quant

This study offers numerical simulation results using the ABAQUS/CAE version 2019 finite element computer application to examine the performance, and residual strength of eight recycle aggregate RC one-way slabs. Six strengthened by NSM CFRP plates were presented to study the impact of several parameters on their structural behavior. The experimental results of four selected slabs under monotonic load, plus one slab under repeated load, were validated numerically. Then the numerical analysis was extended to different parameters investigation, such as the impact of added CFRP length on ultimate load capacity and load-deflection response and the impact of concrete compressive strength value on the structural performance of

  Reaction of Na2PdCl4 with benz-1,3-imidazole-2-thione or (bzimtH) benz-1,3-thiazoline2-thione (bztztH) in ethanol / NE3 afford complexes of the type [Pd(bzimt)2](1) and [Pd(bztzt)2](2) respectively. Treatment of [Pd(L)2] L= bzimt or bztzt with bidentate ligands (N^N) where N^N= bipyridine (Bipy) , phenanthroline (Phen) , ethylene diamine , or N,N′dimethylethylene diamine afford mononuclear complexes of the type [PdL2(N^N)]. The bzimt and bztzt ligands are coordinated as bidentate chelating ligands through the S and N in (1) and (2) whereas bonded as a monodentate fashion via the sulfur atom in other complexes. The prepared complexes were characterized by elemental CHN analysis, ir and 1H nmr spectra.
 

Introduction: Infection control or hospital-acquired infections are the major concern of the health care system and agencies. Critical care nurses are on the first-line contact with the patients, so on, they are most vulnerable to acquired infections. It is really important to regularly check their knowledge and practices concerning infection control. Objectives: The study aims to identify the impact of years’ experience on nurses’ knowledge and practices concerning infection control in three hospitals and center (Baghdad teaching hospital, Ibn Al-Nafees hospital, and Ibn al-Bitar center) Methodology: Cross-sectional study was conducted, the study starting from 4th of July 2020 to 13th of November 2020. Non-probability (purposive) sampl

Background: Diabetes and periodontitis are considered as chronic diseases with a bidirectional relationship between them. This study aimed to determine and compare the severity of periodontal health status and salivary parameters in diabetic and non-diabetic patients with chronic periodontitis. Materials and Methods: Seventy participants were enrolled in this study. The subjects were divided into three groups: Group I: 25 patients had type 2 diabetes mellitus with chronic periodontitis, Group 2: 25 patients had chronic periodontitis and with no history of any systemic diseases, Group 3: 20 subjects had healthy periodontium and were systemically healthy. Unstimulated whole saliva was collected for measurement of salivary flow rate and pH.

Tungsten inert gas arc welding–based shaped metal deposition is a novel additive manufacturing technology which can be used for fabricating solid dense parts by melting a cold wire on a substrate in a layer-by-layer manner via continuous DC arc heat. The shaped metal deposition method would be an alternative way to traditional manufacturing methods, especially for complex featured and large-scale solid parts manufacturing, and it is particularly used for aerospace structural components, manufacturing, and repairing of die/molds and middle-sized dense parts. This article presents the designing, constructing, and controlling of an additive manufacturing system using tungsten inert gas plus wire–based shaped metal deposition metho