When the financial resources of individuals and groups available, this will lead to increase the consumption ranges and sometimes reached to excessive especially to the categories that have little awareness about economic importance and its reflections. it seems that consumerism has increased in many countries including Iraq because of many factors, and the most important one is the availability of financial resources as a result of the increase in oil exports as well as the spread of consumption media department at various levels especially.

Varied uses of international rivers in the past few decades dramatically, resulting in this multiplicity of uses and all associated with it for the occurrence of freshwater scarcity activities, and thus an increase in conflicts and disputes around on the rights of each of the riparian countries to benefit from the waters of the river at various purposes, particularly the establishment of dams on some of them as is the case (Renaissance Ethiopian) big impact on downstream countries Dam (Egypt and Sudan), due to the Oukuahma at the end of the Nile Valley made them vulnerable to environmental fluctuations, political crises facing the Nile basin countries, and any reduction in the proportion of water is not only the Nile River, but for all r

In this work, the effect of partial amounts of gases in gas mixture of a CW CO2 laser on the output power was investigated. Also their effect on the condition determining the glow-discharge self-sustaining required for pumping the active medium was studied. Two fit relations were derived to predict the output laser power and the electric field to unit pressure ratio as functions to the partial amounts of gases. Results presented in this work could be used fruitfully to determine some of the optimum operational conditions of glow-discharge low-power CW CO2 lasers.

The purpose of this study is designate quenching and tempering heat treatment by using Taguchi technique to determine optimal factors of heat treatment (austenitizing temperature, percentage of nanoparticles, type of base media, nanoparticles type and soaking time) for increasing hardness, wear rate and impact energy properties of 420 martensitic stainless steel. An (L₁₈) orthogonal array was chosen for the design of experiment. The optimum process parameters were determined by using signal-to-noise ratio (larger is better) criterion for hardness and impact energy while (Smaller is better) criterion was for the wear rate. The importance levels of process parameters that effect on hardness, wear rate and impact energy propertie

Carbon nanoparticles are prepared by sonication using carbon black powder. The surface morphology of carbon black (CB) and carbon nanoparticles (CNPs) is investigated using scanning electron microscopy (SEM). The particles size ranges from 100 nm to 400 nm for CB and from 10 nm to 100 nm for CNPs. CNPs and CB are mixed with silicon glue of different ratios of 0.025, 0.2, 0.05, and 0.1 to synthesis films. The optical properties of the prepared films are investigated through reflectance and absorbance analyses. The ratio of 0.05 for CNPs and CB is the best for solar paint because of its higher solar water heater efficiency and is then added to the silicon glue . Temperature of cold water and temperature of hot water in storage tank were ta

This research aims to show the sight at the importance of the private banking sector in Iraq and its role in financing of the investment projects , of the ability of Central Bank's decision to increase the minimum limit of capital for private banks to provide support to the economic activity and the development in Iraq. In addition to illustrate the importance of the capital increase, with a, and taking into notice the most important determinants that can stand in front of these banks in the beginning of the decision implementation, which in turn can lead to the most important proceedings that can contribute in the support of banks to implementation the decision.  Also, the research has highlighted the most important ways through wh

This paper is focused on studying the effect of cutting parameters (spindle speed, feed and depth of cut) on the response (temperature and tool life) during turning process. The inserts used in this study are carbide inserts coated with TiAlN (Titanum, Aluminium and Nitride) for machining a shaft of stainless steel 316L. Finite difference method was used to find the temperature distribution. The experimental results were done using infrared camera while the simulation process was performed using Matlab software package. The results showed that the  maximum difference between the experimental and simulation results was equal to 19.3 , so, a good agreement between the experimental and simulation results  was achieved. Tool life w

The study aims to identify the degree of appreciation for the level of digital citizenship of a sample of Palestinian university students in the governorates of Gaza, and its relationship to the level of health awareness about the emerging coronavirus (covid-19). To achieve the objectives of the study, the researcher followed a descriptive approach by applying two questionnaires; the first, which consists of 30 items, was used  to measure the level of digital citizenship.  The second, which consists of 19 items, was used to measure the level of health awareness. Both questionnaires  were applied on a sample of 367 students who were electronically selected using the manner simple randomness. Results have shown that the degr

The formula of Ijarah and Ijarah ending with ownership is one of the investment formulas in Islamic banks, so this research has shed light on it in order to benefit from the experiences of the research sample banks, This research aims to find a reliable way for Iraqi Islamic banks, namely (leasing and leasing ending with ownership) in order to invest their money without usurious interests, The problem of the research emerges through the lack of awareness of the Iraqi Islamic banks to work with different Islamic financing formulas and their inability to invest their money through the adoption of their administrations for different formulas, including the leasing, and this is reflected in the decrease and fluctuation of its profits, Theref

In the spreading of the Internet, mobile smart devices, and interactive websites such as YouTube, the educational video becomes more widespread and deliberative among users. The reasons for its spread are the prevalence of technologies, cheap cost, and easy to use. However, these products often lack to the distinction in video production. By following videos of an educational channel on YouTube, some comments found to discuss the lack of the content presented to motivate the learners, which lead to reduce the viewers of the videos. Therefore, there is an important decision to find general standards for the design and production of educational videos. A list of standards has been drawn up to help those interested in producing educational