Obesity is a common disease that resulted from over-nutrition in adults and children. It rarely causes damage to the centers of food in the brain. Obesity is defined as an increased body weight from its natural limit which is resulted from the accumulation of excessive amounts of fatty tissue incredibly up to 20% in males, 30 % in females unless this increase is not due to an increase in muscles as in athletes or accumulation of water in the body which is resulted from Mesothelioma or the magnitude of the skeleton.Obesity is the increase of the total average of fat in the body compared to other tissues, which causes an increasing body weight, thereby increasing body mass. The fatty child has an increase in the stored fatty layer under the skin, and increased weight 20%more than the normal weight of other children in the same age and height.
This thesis focuses on identifying showing the relationship between obesity and some of the variables. Moreover, the thesis reflects the importance of maintaining the ideal weight of the child and his role in the growth and health. The evidence shows that children who suffer from obesity are more likely to become fat adults, so they are exposed to increased risk of serious health problems. Hence, protecting children from obesity and treating them is possible through changing lifestyle, improving the child's nutrition system, and urging him to exercise to improve their health at the present time and in the future.
Therefore, the thesis aims: to detect significant differences in obesity for kindergarten children depending on certain variables through the testing hypothesis as followed: Statistically there are no significant differences in obesity with kindergarten children that are attributable to the following variables:
(A)Sex variable.
(B) The sequence of the child in the family..
(C) Dietary habits of the family.
To achieve the objectives of this study, 300 children were selected as samples, 166 males and 134 females. One of the most important tools that were used is:
1 - an electronic device for measuring weight.
2 - Length measuring tape.
3 - Measurement of body mass index (BMI)..
The researcher used in data statistical analysis:
(1) One way Anova.
(2) The T- test for two independent samples: Independent Samples Test.
(3) The real bilateral correlation coefficient (Point Bay Cyril).
The most important results that have been reached:
(1) That females suffer from obesity more than males because the body mass index of females is greater than the body mass index (BMI) for males.
(2) There is no statistically significant difference between the averages of body mass index (BMI) scores for kindergarten children due to the variable of the sequence of the child within his brothers.
(3) There is no statistically significant difference between the averages of body mass index (BMI) scores for obese kindergarten children that is attributed to behavioral tendencies variable of the child.
(17)
(14)
(14)
(13)
(2)
In this work, microbubble dispersed air flotation technique was applied for cadmium ions removal from wastewater aqueous solution. Experiments parameters such as pH (3, 4, 5, and 6), initial Cd(II) ions concentration (40, 80, and 120 mg/l) contact time( 2, 5, 10 , 15, and 20min), and surfactant (10, 20and 40mg/l) were studied in order to optimize the best conditions .The experimental results indicate that microbubbles were quite effective in removing cadmium ions and the anionic surfactant SDS was found to be more efficient than cationic CTAB in flotation process. 92.3% maximum removal efficiency achieved through 15min at pH 5, SDS surfactant concentration 20mg/l, flow rate250 cm3/min and at 40mg/l Cd(II) ions initial co
... Show More
(3)
Background: The longevity of any prosthesis depends on the materials from which it was fabricated, that is why, defects in the material properties may reduce the service life of prosthesis and necessitate its replacement. The aim of this study was to evaluate the effect of adding different concentrations of Polyamide-6 (Nylon-6) on the tear and tensile strength of A-2186 RTV silicone elastomer. Materials and Methods: 80 samples were fabricated by the addition of 0%, 1%, 3% and 5% by weight PA-6 micro-particles powder to A-2186 platinum RTV silicone elastomer. The study samples were divided into four (4) groups, each group containing 20 samples. One control group was prepared without PA-6 micro particles and three experimental groups were pr
... Show More
(10)
In this work, the effects of solvent properties on the characteristics of absorption and fluorescence for two laser dyes was studied. Dyes used in this work include Coumarin 5400 and DCM, while the solvents include ethanol, methanol, acetone, propanol and chloroform. Coumarin 5400 dye shows sharp fluorescence peaks in the green band of visible region while the DCM dye shows relatively wide band within 590-630 nm. Therefore, the selection of any dye for random gain medium applications should be performed after determining the most appropriate solvent as the optimum fluorescence characteristics are obtained.
(2)
(2)
(7)
(2)
The efforts embedded in this paper have been devoted to designing, preparing, and testing warm mix asphalt (WMA) mixtures and comparing their behavior against traditional hot mix asphalt mixtures. For WMA preparation, the Sasobit wax additive has been added to a 40/50 asphalt binder with a concentration of 3%. An experimental evaluation has been performed by conducting the Marshall together with volumetric properties, indirect tensile strength, and wheel tracking tests to acquire the tensile strength ratio (TSR), retained stability index (RSI), and rut depth. It was found that the gained benefit of reduction in mixing and compaction temperatures was reversely associated with a noticeable decline in Marshall properties and moisture s
... Show More
(1)
(1)
In the present study, MIG welding is carried out on low carbon steel type (AISI 1015) by using electrode ER308L of 1.5mm diameter with direct current straight polarity (DCSP). The joint geometry is of a single V-butt joint with one pass welding stroke for different plate thicknesses of 6, 8, and 10 mm. In welding experiments, AISI 1015 plates with dimensions of 200×100mm and edge angle of 60o from both sides are utilized. In this work, three main parameters related to MIG welding process are investigated, which are welding current, welding speed, heat input and plate thickness, and to achieve that three groups of plates are employed each one consists of three plates. The results indicate that increasing the weld heat input (t
... Show More