Background: Ceramic veneers represent the treatment of choice in minimally invasive esthetic dentistry; one of the critical factors in their long term success is marginal adaptation. The aim of the present study is to evaluate the marginal gap of ceramic veneers by using two different fabrication techniques and two different designs of preparation. Material and methods: A typodont maxillary central incisor used in the preparation from which metal dies were fabricated, which were in turn used to make forty stone dies. The dies divided into four experimental groups, each group had ten samples: A1: prepared with butt-joint incisal reduction and restored with IPS e.max CAD, A2: prepared with overlapped incisal reduction and restored with IPS e.max CAD. B1: prepared with butt-joint incisal reduction restored with IPS e.max press. B2: prepared with overlapped incisal reduction and restored with IPS e.max press. The marginal gap was measured with direct view technique using digital microscope at a magnification of 230x. Measurements were recorded for four surfaces for each sample and the maximum value was taken to represent that sample. Results: The data were analyzed with two-way ANOVA and independent samples t-tests. These tests revealed highly significant effects of both the preparation design and the technique of fabrication on the marginal gap (p=0.00), with CAD/CAM veneers, group A1 recorded the least marginal gap and pressing group, B2 showed the highest gap values. There was no significant effect of the interaction between the two parameters on the marginal gap. Conclusion: the CAD/CAM veneers with butt joint incisal reduction produced the most accurate margins while the least favorable combination was the pressable ceramic veneers with overlapped incisal reduction.
The aim of this research is to identify the level of health services provided in the health centers operating in the family medicine system in Baghdad, and to determine the extent to which these health centers are applied to the internationally recognized standards , "Defining the quality of service gap between health care centers operating in the family medicine system and the standards adopted by the corresponding international centers (Al-Shabab Model Family Medicine Center, Al-Jahad Family Health Center, Al-Adhamiya Family Health Center, Al-Zawiya Family Health Center), and in view of what our health institutions are facing. The family of primary health care centers has difficulties, obstacles and challenges such as the diffi
... Show More
in this paper sufficient conditions of oscillation of all of nonlinear second order neutral differential eqiation and sifficient conditions for nonoscillatory soloitions to onverage to zero are obtained
Food comes after air and water in terms of importance in the survival of human beings, In addition, it is the support and strength of health and support, if lost or destroyed man would die or get sick and become a heavy burden on himself and his society. Food, like other sources of life, is subject to various risks and corruption comes from countless sources. Among these dangers is the result of spontaneousness, lack of knowledge or compulsion due to the interaction of variables beyond the will of the producer and the consumer, such as pollution of water, air and environment and their reflection on food consumed by people. However, we can’t deny that some reasons of corruption are intentional and resulting from a planning in advance in
... Show More
(2)
(2)
The paper reports the influence of annealing temperature under vacuum for one hour on the some structural and electrical properties of p-type CdTe thin films were grown at room temperature under high vacuum by using thermal evaporation technique with a mean thickness about 600nm. X-ray diffraction analysis confirms the formation of CdTe cubic phase at all annealing temperature. From investigated the electrical properties of CdTe thin films, the electrical conductivity, the majority carrier concentration, and the Hall mobility were found increase with increasing annealing temperatures.
The new events in every era are endless, and it is not required of the legal texts to pursue each event by itself and attach to it its ruling.
At the same time, every event or action must have a Shari’a ruling according to the wise Lawgiver, and our scholars have noted this in every event presented to them. ...etc.
It is well known that reaching the legal ruling on a matter, by examining the detailed evidence, is subject to following the path of the rules and regulations specific to the overall evidence, which we organize on the basis of the principles of jurisprudence.
Therefore, any disagreement about the manner or content of these rules will have an impact on the difference of jurists in partial issues, when examining the d
The purpose of this study is to explore whether the adoption of Beyond Budgeting (BB) as a management accounting practice (MAP) contributes to developing intellectual capital (IC) and creating value in Iraqi companies. This requires an understanding of the views of the Iraqi managers about the nature of the information provided by this practice, which may be used to determine whether this information is relevant in the management of IC in the context of Iraq. This research aims also to explore the challenges of the adoption of the BB in planning and controlling IC in Iraq. The study adopts a qualitative approach and an interpretive paradigm. It also adopts a semi-structured interview method of collecting data from executive managers
... Show More
The paper reports the influence of annealing temperature under vacuum for one hour on the some structural and electrical properties of p-type CdTe thin films were grown at room temperature under high vacuum by using thermal evaporation technique with a mean thickness about 600nm. X-ray diffraction analysis confirms the formation of CdTe cubic phase at all annealing temperature. From investigated the electrical properties of CdTe thin films, the electrical conductivity, the majority carrier concentration, and the Hall mobility were found increase with increasing annealing temperatures.