Background: The bonded orthodontic retainer constructed from multistrand wire and composite is an efficient esthetic retainer, which can be maintained long-term. Clinical failures of bonded orthodontic retainers, most commonly at the wire/composite interface, have been reported. This in vitro investigation aimed to evaluate the tensile forces of selected multistrand wires and composite materials that are available for use in the construction of bonded fixed retainers. Materials and Methods: The study sample includes 120 wires with three types of retainer wires (3 braided strands\ Orthotechnology, 8 braided strands\ G&H Orthodontics, 6 coaxial strands\ Orthoclassic wires), two types of adhesive (flowable\ Orthotechnology, non flowable\ G&H Orthodontics composites) and two thickness of the adhesive (1mm, 2mm). The samples were prepared for each composite in which a wire was embedded; then the composite was light cured for 40 seconds and the specimens were stored in artificial saliva at 37°C in the incubator for 24 hours. The ends of the wire were drawn up and tensile force was applied through Tinius-Olsen universal testing machine until the resin failed and the results were recorded in Newton (N). Results: Statistical analysis showed that there was a highly significant difference (P ≤ 0.01) among the mean values of tensile forces of the three types of retainer wires in each thickness of composite with exception of a non significant difference (P > 0.05) between (3 braided) and (8 braided) and a non significant difference (P > 0.05) between (3 braided) and (6 coaxial) in both thickness of composite, a highly significant difference (P ≤ 0.01) between the two thickness of both composite types in each wire type and a highly significant difference (P ≤ 0.01) between the two types of composite in each wire type of both thickness of composite. Conclusion: The result of this study revealed that the 8 braided strands retainer wire shows the highest values of tensile force among the tested retainer wires, the non flowable composite demonstrates a higher tensile force than the flowable composite and increasing the thickness of composite overlying the wire increased the force required to detach the wire from the composite.
(4)
(3)
(2)
In this work, results from an optical technique (laser speckle technique) for measuring surface roughness was done by using statistical properties of speckle pattern from the point of view of computer image texture analysis. Four calibration relationships were used to cover wide range of measurement with the same laser speckle technique. The first one is based on intensity contrast of the speckle, the second is based on analysis of speckle binary image, the third is on size of speckle pattern spot, and the latest one is based on characterization of the energy feature of the gray level co-occurrence matrices for the speckle pattern. By these calibration relationships surface roughness of an object surface can be evaluated within the
... Show More
In all process industries, the process variables like flow, pressure, level, concentration
and temperature are the main parameters that need to be controlled in both set point
and load changes.
A control system of propylene glycol production in a non isothermal (CSTR) was
developed in this work where the dynamic and control system based on basic mass
and energy balance were carried out.
Inlet concentration and temperature are the two disturbances, while the inlet
volumetric flow rate and the coolant temperature are the two manipulations. The
objective is to maintain constant temperature and concentration within the CSTR.
A dynamic model for non isothermal CSTR is described by a first order plus dead
time (FO
This paper presents the electrical behavior of the top contact/ bottom gate of an organic field-effect transistor (OFET) utilizing Pentacene as a semiconductor layer with two distinctive gate dielectric materials Polyvinylpyrrolidone (PVP) and Zirconium oxide (ZrO2) were chosen. The influence of the monolayer and bilayer gates insulator on OFET performance was investigated. MATLAB software was used to simulate and determine the electrical characteristics of a device. The output and transfer characteristics were studied for ZrO2, PVP and ZrO2/PVP as an organic gate insulator layer. Both characteristics show a high drain current at the gate dielectric ZrO2/PVP equal to -0.0031A and -0.0015A for output and transfer characteristics respectively
... Show More
(3)
(4)
(1)
The grain hardness, wet and dry gluten contents, protein and ash contents are determined in grains from different cultivars of wheat which are important in food products, either which are present in raw materials or in final products. Wheat is also a very important food raw material, and flour as the final product of milling. The importance of knowing the physical and chemical properties of wheat and flour is due to the determination of quality and kind of flour which is produced after the milling process. In this work, some physical and chemical properties of different wheat cultivars are determined and the comparisons of these characteristics are performed in both wheat and flour. Uruq Wheat sample (W5) has the highest results when compar
... Show More
(2)
Generally, there are many problems that people run into; unemployment is one of these common diseases which usually hits the whole communities leaving crucial effects (economic, social, and psychological) that are difficult to handle them. The current study aims to identify the level of emotional disorders among Iraqi unemployed alumni for the academic years (2013-2016). To this end, the researchers have prepared a questionnaire to measure (anxiety, depression, and anger): these criteria distributed over (30) item. As for sample, it limited to (50) male and female student. The findings of study have revealed that the whole sample showed a high level of emotional disorders, and anger disorder showed higher level than the level of (depress
... Show MoreDBN Rashid, Rimak International Journal of Humanities and Social Sciences, 2020
This paper studies the demonstratives as deictic expressions in Standard Arabic and English by outlining their phonological, syntactic and semantic properties in the two languages. On the basis of the outcome of this outline, a contrastive study of the linguistic properties of this group of deictic expressions in the two languages is conducted next. The aim is to find out what generalizations could be made from the results of this contrastive study.