This work involves the synthesis and characterization of asymmetrical pyromellitdiimide
derivatives [IV]a-f
by four sequence steps selective reaction . One mole of pyromellitic dianhydride
was reacted with one mole of various primary aromatic amines [ 4-nitro aniline , 4-chloro aniline , 4-toludine and 4-anisidine] in excess of dry acetone to produce six compounds (N-substituted-pyromellitamic monoacid) [I]a-f . These new compounds [I]a-d were converted to the corresponding
N- substituted- pyromellitmonoimide [II]a-d via their heating at (80-90)
0
C in sodium acetate-acetic
anhydride mixture .
The compounds [II]a-f
were allowed to react with one mole of another primary amines in
excess of dry acetone t

This work comprises the synthesis of 18 new N- substituted 5,10-
dihydrophenophosphazine.The diphenylamine was chosen as the starting material ,
which was reacted with phosphorus trichloride at elevated temperature (200-220)0C
for 6 hrs, followed by treating the reaction mixture with water to yield 5,10-
dihydrophenophosphazine-10-oxide(1), this was reacted with ethylchloroacetat to
obtain ethyl(5,10-dihydrophenophosphazine-10- oxide)acetate(2). Compound (2)
was converted to acid hydrazide by treating with hydrazine hydrate( 98% ) to obtain
5-(5,10-dihydrophenophosphazine) acetohydrazide-10-oxide (3). The acid hydrazid
was used to react with phenylisocyanat , phenylthioisocyanat to give (4,7)
respectively which

This work involved the co-substitution of the two bioactive ions of strontium and magnesium into the hydroxyapatite (HA) coating which was then electrochemically deposited on Ti-6Al-4V ELI dental alloy (Gr.23) before and after treatment by Micro Arc Oxidation (MAO). The deposited layers were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The adhesion strength of the coating layer was estimated by using pull-off adhesion test. The adhesion strength of Sr/Mg-HA on the Ti-6Al-4V ELI dental alloy after MAO treatment was 1.79 MPa, which was higher than that before MAO treatment (1.62 MPa). The corrosion behavior of th

The Mannich base ligand was synthesized in an ethanol medium through a condensation reaction of 2-mercaptobenzimidazole and ciprofloxacin at room temperature. Subsequently, several metal complexes of this ligand were prepared. To characterize both the base ligand and the metal complexes, various techniques were employed, including elemental analysis, FT-IR spectroscopy, UV-Vis spectroscopy, molar conductivity measurements, magnetic moment determination, and melting point analysis. The results were shown that the metal complexes formed have the formula [Cr(L)2Cl2] Cl.H2O and [Rh(L)2(H2O)2] Cl3.H2O, where L= mannich base ligand. Based on spectroscopic analytical, coordination with metal ions involves the 'N' donor atom of mannich base

The Effect of Chicken Eggshell Extract on Microhardness of Artificially Induced Dental Erosion in Permanent Teeth (In Vitro Study), Shatha A Abbas*, Alhan A Qasim

SYNTHESIS AND CHARACTERISATION OF NEWCo(II), Zn(II) AND Cd(II) COMPLEXES DERIVED FROM OXADIAZOLE LIGAND AND 1,10-PHENANTHROLINE AS Co-LIGAND

In this work, prepared new ligand namely 5-(2,4-dichloro-phenyl)-1,3,4-oxadiazole-2-(3H)-thion, was obtained from the 2,4-dichlorobenzoyl chloride with hydrazine, after that reaxtion with CS2/KOH in methanol.

         The main objective of this research is to design and select a composite plate to be used in fabricating wing skins of light unman air vehicle (UAV). The mechanical properties, weight and cost are the basis criteria of this selection. The fiber volume fraction, fillers and type of fiber with three levels for each were considered to optimize the composite plate selection. Finite element method was used to investigate the stress distribution on the wing at cruise flight condition in addition to estimate the maximum stress. An experiments plan has been designed to get the data on the basis of Taguchi technique. The most effective parameters at the process to be find out by employing L₉

Background: The Initial (primary) stability is one of the factors that play an important role in the success of the dental implants. The purpose of this study was to evaluate the initial stability of dental implant with horizontal plate by using five analytical tests: insertion torque, removal torque, resonance frequency analysis, push-in test and pull-out test. Materials and methods: Two different lengths of dental implants (5mm and 10mm) were tested in this study; each dental implant was 4mm in diameter with a square threads shape of 1mm pitch and 0.5mm depth. The crestal area was 4.2mm diameter contained a right angle margin circumferential ring while the apical area was tapered with two self-tapping grooves. In this study, the initial s