Bleeding disorders in pediatrics is an important issue and can be lifethreatening if not diagnosed and treated appropriately. We aimed to evaluate Iraqi pediatric practice (as an example of resource-limited settings) about the use of Recombinant Activated Factor VII (RFVIIa) in bleeding disorders, with emphasis on its effectiveness and safety, in comparison with adjuvant therapy. Budget restrictions may affect the availability of even lifesaving drugs such as (RFVIIa). Therefore, we tried to investigate the local experience of pediatric bleeding, with the evaluation of the potential ability of adjuvant therapy of blood products and vitamin K to substitute RFVIIa in case of non-availability. During a complete one year‘s period, 35 patients

This study revealed the efficiency of Bacillus subtilisin degrading two textile dyes (disperse red and disperse yellow), the rates of red dye removal when measured after 24, 48, 72 and 96 hours for the concentrations of 50 ppm were 51.67, 67.56, 84.67 and 95.33%, for the concentration 150 ppm were 41.67, 62.67, 80.67 and 89.67%, while for the concentration 300 ppm were 25.67, 42.67, 71.67 and 84.33%. The results of yellow dye removal showed that the concentration of 50 ppm were 49.67, 65.33, 83.33 and 92.67%, for the concentration of 150 ppm were 38.33, 60.33, 77.33 and 87.33%, and for the concentration, 300 ppm were 24, 36.67, 68.33 and 81.67%, when measured after 24, 48, 72 and 96 hours. Results recorded a slight decrease in pH valu

the structrual and mechanical properties of thin Ni films of different thicknesses deposited on coring glass substrate using lonbeam sputtering(IBS) technique under vacuum torr have been studied the TEM and electron

The aim of this research is to benefit from recycl the aircraft waste oils which is discarded in sewage network, to be used in preparation of greases for industrial purposes and to reduce the environmental pollution. In this research synthetic greases were prepared with special specifications by mixing the waste oils after treating with (silica gel as adsorbent agent, and filtration to precipitate impurities then heated to 110 C? to get rid of water) bentonite produced in Iraq which is available and cheap with existence of high density polyethylene at specific conditions of ( heating and mixing) . The best weight proportion were reached, then paraffin wax and additives were added to improve the properties of grease and give the

A number of juices, jams, canned foods and frozen fishes available in local markets were inspected with respect to microbial contamination. We have determined the total viable bacterial cell counts in these samples and the number of g(-) lactose fermentors as a bacterial indicator of food spoilage. The results indicated that most of the food items inspected, were contaminated with large numbers of different species of g(-) ,g(+), yeast and fungi and some were contained more than the maximum permissible number of pathogenic g(-) enteric E-coli, which render these food items unsafe for human consumption.

This paper presents the application of nonlinear finite element models in the analysis of dappedends pre-stressed reinforced concrete girders under static loading by using ANSYS software. The girder dimensions are (4.90 m span, 0.40 m depth, 0.20 m width, 0.20 m nib depth, and 0.10 m nib length) and the parameters considered in this research are the pre-stress effect, and strand profile (straight and draped). The numerical results are compared with the experimental results of the same girders. The comparisons are carried out in terms of initial prestress effect, load- deflection curve, and failure load. Good agreement was obtained between the analytical and experimental results. Even that, the numerical model was stiffer than the experiment

The CIGS/CdS p-n junction thin films were fabricated and deposited at room temperature with rate of deposition 5, and 6 nm secG1 , on ITO glass substrates with 1mm thickness by thermal evaporation technique at high vacuum pressure 2×10G5 mbar, with area of 1 cm2 and Aluminum electrode as back contact. The thickness of absorber layer (CIGS) was 1 µm while the thickness of the window layer CdS film was 300 nm. The X-ray Diffraction results have shown that all thin films were polycrystalline with orientation of 112 and 211 for CIGS thin films and 111 for CdS films. The direct energy gaps for CIGS and CdS thin films were 1.85 and 2.4 eV, respectively. Atomic Force Microscopy measurement proves that both films CIGS and CdS films have nanostru

Modern emerged technologies impose development and fabrication of miniatur-ized parts and devices in the micro- and nano-scale. Producing micro- and nano-featured structures requires nonconventional machining processes where con-ventional machining processes such as grinding, milling and eroding have failed. New emerging processes, such laser machining processes, are still fraught with almost invincible processes. Micro-/nano-machining are the pro-cesses of producing parts, microsystems or features at a scale of a few microm-eters and less than one hundred nanometers, respectively. Precise cutting and clean material removal accompanied with a negligible heat affected zone (HAZ), which are usually the characteristics of laser ablation, have

BACKGROUND: Papillary thyroid carcinoma (PTC) is the most common type of thyroid carcinoma that represents a set of characteristic of nuclear features in which the diagnosis is depend. AIM: The study aimed to review different variants of PTC which has different malignant potential in correlation with many prognostic and clinical factors in Iraq. PATIENTS AND METHODS: Paraffin blocks of 227 cases of PTC were selected, subtyped, and grouped according to the malignant potential. The prognostic and clinical factors were studied. RESULTS: The mean age was (39.29 ± 12.17) years, with female predominance (86.3%), where (55.5%) of them below 40 years, conventional variant was most common (40.1%), followed by papillary microcarcinoma