Aim: The study designed to evaluate the Geno-protective effect of green tea extract against genotoxicity induced by metronidazole and tinidazole. Methods: Thirty-six mice were used, For each experiment, The animals divided into 6 groups: Group I- Negative control administered distilled water; Group II-Healthy mice treated with metronidazole alone, Group III- Healthy mice treated with tinidazole alone; Group IV- Healthy mice administered green tea extract alone Group V- Healthy mice treated with metronidazole, followed by green tea extract administration, Group VI- Healthy mice treated with tinidazole, followed by administration of green tea extract. Results: treatment with Tinidazole significantly increase total chromosomal aberration (0.18

In gene regulation, transcription factors (TFs) play a key function. It transmits genetic information from DNA to messenger RNA during the process of DNA transcription. During this step, the transcription factor binds to a segment of the DNA sequence known as Transcription Factor Binding Sites (TFBS). The goal of this study is to build a model that predicts whether or not a DNA binding site attaches to a certain transcription factor (TF). TFs are regulatory molecules that bind to particular sequence motifs in the gene to induce or restrict targeted gene transcription. Two classification methods will be used, which are support vector machine (SVM) and kernel logistic regression (KLR). Moreover, the KLR algorithm depends on another regress

The aerodynamic characteristics of the forward swept wing aircraft have been studied theoretically and experimentally. Low order panel method with the Dirichlet boundary condition have been used to solve the case of the steady, inviscid and compressible flow. Experimentally, a model was manufactured from wood to carry out the tests. The primary objective of the experimental work was the measurements of the wake dimensions and orientation, velocity defect along the wake and the wake thickness. A blower type low speed (open jet) wind tunnel was used in the experimental work. The mean velocity at the test section was (9.3 m/s) and the Reynolds number based on the mean aerodynamic chord and the mean velocity was (0.46x105). The measurements sho

Hydrocarbon production might cause changes in dynamic reservoir properties. Thus the consideration of the mechanical stability of a formation under different conditions of drilling or production is a very important issue, and basic mechanical properties of the formation should be determined. There is considerable evidence, gathered from laboratory measurements in the field of Rock Mechanics, showing a good correlation between intrinsic rock strength and the dynamic elastic constant determined from sonic-velocity and density measurements. The values of the mechanical properties determined from log data, such as the dynamic elastic constants derived from the measurement of the elastic wave velocities in the material, should be more accurate t

The research, whose goal was to study students' failure in secondary school in Iraq, found that 50% of the Iraqi governorates achieved the lowest student failure rates, and Baghdad governorate had the highest percentage of repeaters. And that half of the provinces in Iraq have males constitute 70% of the repeaters, and failure in the exam represented 79.7% of the reasons for failure, and that half of the students who failed are confined to the first and third intermediate grades at a rate of 51.9% , and the research revealed that the security instability was the most influential factor in Students fai

An experiment was conducted to study how SAE 50 engine oil contaminated with diesel fuel affects engine performance. The engine oil was contaminated with diesel fuel at concentrations of 0%, 1%, and 3%. The following performance characteristics were studied: brake-specific fuel consumption, brake thermal efficiency, friction power, and exhaust gas temperature. Each treatment was tested three times. The three treatments (0%, 1%, and 3%) were analyzed statistically with a one-way ANOVA model at the 5% probability level to determine if the three treatments produced significant differences in engine performance. The statistical results showed that there were significant differences in engine performance metrics among the three treatments. The 3

(3) (PDF) Theoretical calculation of the electronic current at N3 contact with TiO2 solar cell devices. Available from: https://www.researchgate.net/publication/362780274_Theoretical_calculation_of_the_electronic_current_at_N3_contact_with_TiO2_solar_cell_devices [accessed May 01 2023].

CdS Nps (inorganic material) was prepared by the chemical reaction method. ZnPc (organic material) and CdS thin films were prepared separately to compare their characterization with the hybrid BHJ blend ZnPc/CdS thin film (2ml:2ml) by spin coating technique. The structural and morphological properties of the prepared thin films have been measured by XRD and AFM respectively. The XRD pattern for both as-deposited and annealed CdS nanoparticle films shows a hexagonal structure. The crystallite size behavior of as deposited ZnPc films and annealing at 423K for 1h, 2h and 3h was approximately similar to the behavior of heat treated blended films. The grain size was measured by AFM, which decreaseds with annealing temperature for ZnPc films,

The aim of this study was to use low cost adsorbents, which consist of corn cobs as plant wastes adsorbents in treatment of Industrial waste water by fixed bed column technique and study the effect of two variables (pH value and contact time). The sample of plant waste (Corn cobs) was tested to determine its activity which gives the best performance in heavy metals removal and other pollutants (TSS, TDS and COD). Adsorption tests showed the corn cobs adsorbents had significant heavy metal removal efficiency. The best removal efficiency 95.05% of Cr was occurred at pH 5.4 and 4.18hr. Higher removal efficiency 99.90% of Ni was occurred at pH 6.5 and 2.38hr. While, lower removal efficiency 91.35% for Zn obtained at pH 6.5 and 0.15hr. Remova