This study includes six species related to the genus Echinops L. (composite) grown in Iraq which are listed below: E.armatus Boiss. & Hausskn., E. bicolor Nabelek, E. cephalotes DC., E.haussknechtii Boiss., E. moulensis Rech., E. nitens Bornm., the geographical distribution and ecological preferences' were documented.
It has been also observed that this genus was distributed near waterfalls, vallies, road side, dry limestone, clay soil and hard rocky soil in Different heights. The most separated species was E.armatus and the least separated one was E.haussknechtii, the species was listed in diagram and distributed on a map.

      This research concern to analyse and simulate the temperature distribution in the spot welding joints using tungsten arc welding shielded with inert gas (TIG Spot) for the aluminum-magnesium alloy type  (5052-O).

      The effect of and the quantity of the heat input that enter the weld zone has been investigated welding current, welding time and arc length on temperature distribution. The finite element method (by utilizing programme ANSYS 5.4) is presented  the temperature distribution in a circular weld pool and the weld pool penetration (depth of welding) through the top sheet ,across the interface into the lower sheet forming a weld spot.   &nbs

The current research deals with studying the petrophysical properties represented by the porosity and its distribution on the level of all units of the top and bottom of the Kirkuk Formation Group. The study area is located in Maysan province in the south-eastern part of Iraq in the Amara field. The Kirkuk Group was deposited in the Tertiary Age. The post-stack method using seismic inversion and creating a relationship between seismic data was accomplished using Hampson-Russel software at well Am-1 and Seismic lines Ama 20 and 30. The research results indicate high porosity values on top of the formation with a decrease in acoustic impedance (Z) and, therefore, a reduction in the density. At the same time, low porosity values were indica

Finite element modeling of transient temperature distribution is used to understand physical phenomena occurring during the dwell (penetration) phase and moving of welding tool in friction stir welding (FSW) of 5mm plate made of 7020-T53 aluminum alloy at 1400rpm and 40mm/min.
Thermocouples are used in locations near to the pin and under shoulder surface to study the welding tool penetration in the workpiece in advance and retreate sides along welding line in three positions (penetrate (start welding) , mid, pullout (end welding)).
Numerical results of ANSYS 12.0 package are compared to experimental data including axial load measurements at different tool rotational speeds (710rpm.900rpm.1120rpm and 1400rpm) Based on the experiment

In this study, new derivatives of 3-C-spiro ring nucleoside analogues were synthesized. The structures of these derivatives were characterized by infrared spectroscopy,1HNMR (some of them) and elemental analysis. The nucleoside derivatives were tested for inhibition of E-coli and were all found to be active.

The Fylex extract exert a high inhibition effect against A . flavus growth on PDA medium, as the fungus growth was completely inhibited by 100% at a concentration of 0.2 and 0.3% of studied extract, while the lowest inhibition percentage (71%) was found at a concentration of 0.1%. Whereas magnesium oxide nanoparticles showed the highest inhibition ratio of A. flavus (100%) was detected at 0.2% and the lowest inhibition ratio (81.66%) was at concentration 0.5%. Moreover, the addition of G. lucidum powder to PDA medium with a concentration of 2.5 mg increased the inhibition rate of A. flavus growth which was 54.4%, while the lowest inhibition ration (18.22%) was found at a concentration of 1000 mg. The milky liquid (brocade milk) of Calotropi

     The Exponentiated Lomax Distribution is considered one of the most commonly used continuous distribution which has a major role in analysing and modelling life time data. Therefore, A family was formed for the Exponential Lomax Distribution by introducing two new distributions as special case of the Exponentiated Lomax Distribution: (Modified Exponentiated Lomax Distribution (MELD) and Restricted Exponentiated Lomax Distribution (RELD. Furthermore, to assess the usefulness and flexibility, the two distributions were applied upon simulation study besides real application with real data set. The simulation results clearly shown the flexible performance of the maximum likelihood estimators for the parameter. Also, the real applicat