Objective(s): The present study aims at assessing the prevalence of smoking among health workers in Baghdad Teaching Hospital and to find out the effectiveness of instructional booklet concerning risk of smoking on health workers′ knowledge in hospital.
Methodology: A pre-experimental design study was conducted from 1st of October 2019 to 17th of March 2020. A non-probability sample consists of (500) participant (343 non-smokers and 157 smokers) from (1500) health workers in Baghdad Teaching Hospital, they included the physicians, nurses, pharmacists, physiotherapists, Laboratory Technicians, Medical Assistants. A questionnaire is constructed to evaluate the effectiveness of instructional booklet on health workers’ knowledge about risks of smoking which consists of (33) items. Reliability of the questionnaire is determined through the use of internal consistency reliability and the computation of Cronbach Alpha Correlation Coefficient which is equal to (0.905) and the content validity of the questionnaire is determined through a panel of experts.
Results: The results of the study show that there is improvement of smokers’ knowledge concerning the effect of smoking on personal health status which is (50.9%), high percent of them not have enough knowledge at pretest while the improved their knowledge at posttest to (81.6%), and their knowledge about risk of smoking on hospital environment is improved from (51.6%) at pretest to (86.38%) at posttest, and there is a highly significant between the effectiveness of the instructional booklet and health workers’ knowledge about the risk of smoking on personal health at P ≤ 0.05 level.
Recommendations: The study recommends that extensive and comprehensive studies, at the national level, could be conducted to improve the knowledge of health workers regarding the risks of smoking to human health and environment, and work to apply the penal code to the smokers inside hospitals and health institutions.
This research aims to investigate the effect of four types of nanomaterial on the Marshall properties and durability of warm mix asphalt (WMA). These types are; nano silica(NS), nano carbonate calcium (NCC), nano clay(NC), and nanoplatelets (NP). For each type of Nanomaterial, three contents are tried as following; NS(1%, 3%, and 5%), NCC(2%, 4%, and 6%), NC(3%, 5%, and 7%), and NP (2%, 4%, and 6%) by weight of asphalt cement. Following Marhsall mix design method, the optimum asphalt cement content is determined, thereafter the optimum dosage for each nanomaterial is obtained based on the highest Marshall stability value. The durability of the control mix (no nanomaterial) and modified mixtures have been compared based on moisture damage, r
... Show More
(10)
(8)
Epoxy (EP) – Silica (SiO2) composites are well known composites used in microelectronic industry . So it is important to study their dielectric behavior under different conditions such as
the presence carbon black (UV absorber) and immersion in the water for 30 days .
Dielectric properties were calculated over the frequency range 102 – 106 Hz for epoxy composites with different weight % of micrometer 1.5μm SiO2 particles (60%, 65% and 70wt%) modified with 0.5wt% silane coupling agent to improve adhesion between EP and SiO2 phases .
In this paper a thin films of selenium was prepare on substrates of n-Si by evaporation in a vacuum technique with thickness about 0.5μm. And then an annealing process was done on samples at two temperature (100 and 200) C ° in a vacuum furnace (10-3 torr).
Some structural, optical and mechanical properties of prepared thin films were measured. Results showed that the prepared film was the crystallization, optical transmittance and micro hardness of the prepared thin films increased significantly after annealing.
(1)
(1)
(7)
(5)
objective: To evaluate the influence of monolithic zirconia brand, thickness, and substrate color on color matching accuracy when optically coupled to abutment substrates. Methods: A total of 180 samples of two brands of monolithic zirconia [Prettau Anterior (PA), Ceramill Zolid FX Multicolor (CZ)] were prepared in three different thicknesses (0.8 mm, 1.5 mm, and 2 mm) with a standardized 10 mm diameter. Color properties of the samples were assessed using spectrophotometry at baseline and after coupling to three substrate types: standard dentin, discolored dentin, and titanium. Color differences (ΔE) were calculated and statistically analyzed by 3-way ANOVA and pairwise comparison ( α=0.05). Results: The brand and material thickness, at
... Show More
(2)
(2)
(116)
(120)
This article examines and proposes a dietary chain model with a prey shelter and alternative food sources. It is anticipated that mid-predators' availability is positively correlated with the number of refuges. The solution's existence and exclusivity are examined. It is established that the solution is bounded. It is explored whether all potential equilibrium points exist and are locally stable. The Lyapunov approach is used to investigate the equilibrium points' worldwide stability. Utilizing a Sotomayor theorem application, local bifurcation is studied. Numerical simulation is used to better comprehend the dynamics of the model and define the control set of parameters.
(12)
(5)
An investigation was conducted for the improvement of viscosity index of light lubricating oil fraction (40 stock)
obtained from vacuum distillation unit of lube oil plant of Daura Refinery, using solvent extraction process.
In this study furfural solvent was used to extract the undesirable materials which reduce the viscosity index of raw
lubricating oil fraction.
The studied effecting variables of extraction were extraction temperature range from 70 to 110°C, and solvent to oil
ratio range from 1:1 to 4:1 (wt/wt).
The n-d-M method was used for calculation of carbon distribution and structural group analysis of the raffinate
produced from furfural extraction.
Also the three component phase diagram for a mixed-ba
(35)
(34)