Molar conductance (Λ) of ionizable side chains amino acids, lysine (Lys) and arginine (Arg) with dehydroascorbic acid (DHA) in water and in NaCl solutions was measured at temperatures range 298 K to 313 K. The limited molar conductance (Λo) and the constant of the ions association (KA) are calculated using the Shedlovsky techniques. The dynamic radius of the concerned ion (R) is calculated by used Stokes–Einstein relation. The heat of association, the Gibbs free energy, the change of entropy and activation energy (ΔHo/ kJ mol-1, ΔGo/ kJ mol-1, ΔSo/J K-1 mol-1, and ΔES/ kJ mol-1) respectively), also calculated. The data show increases the molar conductance with increase in temperature and decreasing in values at addition of DHA to Lys and Arg solutions. The association ions in NaCl solutions appear to increase in radius and decrease in diffusion coefficient relative to water solutions.
ΔES, shows in most samples a positive value for the association and the values in NaCl solutions has lower relative to the water solutions. ΔGo is a trend to decrease with an increase in DHA concentration in water and NaCl solutions. The ion association is exothermic reaction relative to the negative value of ΔHo. The ΔSo and
ΔHo results, for Lys and Arg solutions, show decreasing in values at increase in DHA concentration in water and NaCl solutions. ΔGo (kJ mol-1), ΔSo (J K-1 mol-1), ΔHo (kJ mol-1), and ΔEs (kJ mol-1)
The present investigation is concerned for the purification of impure zinc oxide (80-85 wt %) by using petroleum coke
(carbon content is 76 wt %) as reducing agent for the impure zinc oxide to provide pure zinc vapor, which will be
oxidized later by air to the pure zinc oxide.
The operating conditions of the reaction were studied in detail which are, reaction time within the range (10 to 30 min),
reaction temperature (900 to 1100 oC), air flow rate (0.2 to 1 l/min) and weight percentage of the reducing agent
(petroleum coke) in the feed (14 to 30 wt %).
The best operating conditions were (30 min) for the reaction time, (1100 oC) for the reaction temperature, (1 l/min) for
the air flow rate, and (30 wt %) of reducing
This is prospective study began in Jan. 2003 and concluded in April 2004, was undertaken to examine the benefits of 810 nm diode laser in treatment of four patient with bilateral vocal cord paralysis also to compare the results with conventional treatment Material and methods: 810 nm diode laser 15 watts was used in these cases under general anesthesia, and induction of anesthetic drug done through tracheostomy tube in all patients. All patients were decanulated “Tracheostomy tube removed”, the voice of all preserved within normal. Laser surgery in this case has more benefit and advantage than conventional methods even if the patient need more than on session of laser operation because of high success rate, less complication and easy
... Show MoreThe parameters of resistance spot welding (RSW) performed on low strength commercial aluminum sheets are investigated experimentally, the performance requirements and weldability issues were driven the choice of a specific aluminum alloy that was AA1050. RSW aluminum alloys has a major problem of inconsistent quality from weld to weld comparing with welding steel
alloys sheet, due to the higher thermal conductivity, higher thermal expansion, narrow plastic temperature range, and lower electrical resistivity. Much effort has been devoted to the study of describing the relation between the parameters of the process (welding current, welding time, and electrode force) and weld strength. Shear-tensile strength tests were performed to ind
We studied at the morphology, structural setup, and optical characteristics of thin cadmium (CdSe) films a thickness of 250 nm that were created by thermal evaporation over glass, The films exhibited a hexagonal shape were crystalline, and tended to form grains in the (111) crystallographic direction, according to the X-ray diffraction examinations. These characteristics were established using the investigation's findings. Through the use of thin films of CdSe doped with Ag at a concentration of 1.5%, the crystal structure orientations for pure CdSe (25.32, 41.84) and CdSe:Ag (25.39, 41.01) that were both pure as well as those that were doped with silver were both determined. The band gap of the optical spectrum decreased by 1.93–
... Show MoreThe research aims to develop and build a plasma jet system operating under atmospheric pressure.for biological purposes. The advanced plasma system consists of a power supply and a plasma torch. The source of the development of the system is a previous laboratory system that was developed by changing the voltage and frequency of the power supply, as the power provider equips the system with a voltage in the form of a sine wave whose value is fixed at about (7.5kV) peak to peak and its frequency is about (28 kHz). The plasma torch consists of a teflon tube with of width of (10 m ) located at (10mm) from the end of the tube. The current waveform and voltage wave were measured using a current and voltage sensor and an oscilloscop
... Show MoreA total of 100 clinical sample from (urine, sputum and swabs of wound , burn and ear) were collected from patients in different hospitals of Baghdad during the period from December 2013 to May 2014. 15 isolates (15%) identified belong to Acinetobacter baumannii, swabs of wounds were represented in high percentage of A.baumannii isolates (40%) while percentage of other samples were variable. Susceptibility of 15 A.baumannii isolates were tested toward 16 different Antimicrobial agents, the results showed all isolates were multi drug resistant. In addition, Polymerase Chain Reaction Technique (PCR) was performed to detection the resistance genes encoding the Oxacillinases enzymes. The PCR analysis showed that the presence of insertion sequ
... Show MoreIn this paper had been studied the characterization of the nanocatalyst (NiO) Mesh electrodes. For fuel cell. The catalyst is prepared and also the electrodes The structural were studied through the analysis of X-ray diffraction of the prepared nanocatalyst for determining the yielding phase and atomic force microscope to identify the roughness of prepared catalyst surface, Use has been nanocatalyst led to optimization of cell voltage, current densities & power for a fuel cell.
Study of the development of an activated carbon nanotube catalyst for alkaline fuel cell technology. Through the prepared carbon nanotubes catalyst by an electrochemical deposition technique. Different analytical approaches such as X-ray diffraction (XRD) to determine the structural properties and Scanning Electron Microscope (SEM), were used to characterize, Mesh stainless steel catalyst substrate had an envelope structure and a large surface area. Voltages were also obtained at 1.83 V and current at 3.2 A of alkaline fuel cell. In addition, study the characterization of the electrochemical parameters.
Test results of nine reinforced concrete one way slab with and without lacing reinforcement are reported. The tests were designed to study the effect of the lacing reinforcement on the flexural response of one way slabs. The test parameters were considered is the lacing steel ratios of (0, 0.0025, 0.0045, and 0.0065), flexural steel ratios of (0.0025, 0.0045, and 0.0065) and span to the effective depth ratios of (11, 13, and 16). Two specimens had no lacing reinforcement and the remaining seven specimens had the lacing reinforcement. Four point bending test were carried out, one of the specimens was tested under the static load applied gradually up to failure and the other specimens were tested under repeated load (5 cyc
... Show More