Probit analysis is a type of regression used to analyze the relationship between a stimulus and the quantal response. Allelopathy refers to direct or indirect negative or positive effects of one plant on another through the release of chemical compounds into the environment. This study was carried out to apply probit analysis in investigating the allelopathic effects of the leaves aqueous extracts of apple of Sodom [Calotropis procera (Aiton) W.T.] on the inhibition of seed germination of African rattlebox (Crotalaria saltiana Andr.). A laboratory experiments were carried out at the Faculty of Agricultural Sciences, University of Gezira, Sudan in season 2014/15. Ten concentrations (2.3, 4.6, 7.0, 9.3, 11.6, 13.9, 16.2, 18.5, 20.8 and 23.2 g/l) leaves aqueous extract of apple of Sodom were prepared from the stock solution (50 g / l). A control with sterilized-distilled water was included for comparison. Treatments were arranged in completely randomized design with four replicates. The seeds were examined for inhibition (%) in germination at three days after initial germination. Collected data were transformed using Abbott’s formula and subjected to probit analysis procedure (P £ 0.5). The results showed that the leaves aqueous extract of apple of Sadom had allelopathic effects on seed germination of African rattlebox and there was direct positive relationship between concentration (g/l) and inhibition (%). Also, the data indicated that plotting of corrected inhibition (%) against concentration (%) formed a sigmoid curve. Probit analysis transformed the sigmoid concentration-response curve to a straight line. Hence, the LC25 (2.16 g/l), LC50 (8.55 g/l) and LC75 (33.88 g/l) were accurately estimated. It was concluded that probit analysis is appropriate procedure in studying the allelopathy phenomenon.
was studied by taking several different values for the constant α and fixing the other three variables β, c and d with the values 25.58, -0.7142857, and -1.142, respectively. The purpose of this paper is to know the values by which the system transforms from a steady state to a chaotic state under the initial conditions x, y, and z that equal -1.6, 0 and 1.6 respectively. It was found that when the value of α is equal to 0, the Chua system is in a steady state, and when the value of α is equal to 9.5 and the wave is sinusoidal, the system is in oscillation, and when α is equal 13.4 the system is in a Quasi-chaotic state, and finally the system turns to the chaotic state when the value of α equals 15.0
... Show More
(11)
(3)
As a result of the increase in wireless applications, this led to a spectrum problem, which was often a significant restriction. However, a wide bandwidth (more than two-thirds of the available) remains wasted due to inappropriate usage. As a consequence, the quality of the service of the system was impacted. This problem was resolved by using cognitive radio that provides opportunistic sharing or utilization of the spectrum. This paper analyzes the performance of the cognitive radio spectrum sensing algorithm for the energy detector, which implemented by using a MATLAB Mfile version (2018b). The signal to noise ratio SNR vs. Pd probability of detection for OFDM and SNR vs. BER with CP cyclic prefix with energy dete
... Show More
(1)
In this work the analysis of laser beam profile system ,using a two dimensional CCD (Charge Coupled Device) arrays, is established. The system is capable of producing video graphics that give a two dimensional image of laser beam. The video graphics system creates color distribution that represent the intensity distribution of the laser beam or the energy profile of the beam. The software used is capable of analyzing and displaying the profile in four different methods that is , color code intensity contouring , intensity shareholding, intensity cross section along two dimension x-y, and three dimensional plot of the beam intensity given in the same display.
This study is concerned with the effect of adding two kinds of ceramic materials on the mechanical properties of (Al-7%Si- 0.3%Mg) alloy, which are zirconia with particle size (20μm > P.S ≥ 0.1μm) and alumina with particle size (20μm > P.S ≥ 0.1μm) and adding them to the alloy with weight ratios (0.2, 0.4, 0.6, 0.8 and 1%). Stirring casting method has been used to make composite material by using vortex technique which is used to pull the particles to inside the melted metals and distributed them homogenously.
After that solution treatment was done to the samples at (520ºC) and artificial ageing at (170ºC) in different times, it has been noticed that the values of hardness is increased with the aging time of the o
... Show MoreIn this paper, the system of the power plant has been investigated as a special type of industrial systems, which has a significant role in improving societies since the electrical energy has entered all kinds of industries, and it is considered as the artery of modern life.
The aim of this research is to construct a programming system, which could be used to identify the most important failure modes that are occur in a steam type of power plants. Also the effects and reasons of each failure mode could be analyzed through the usage of this programming system reaching to the basic events (main reasons) that causing each failure mode. The construction of this system for FMEA is dependi
... Show More
Liquid membrane electrodes for the determination iron(III) were constructed based on chloramphenicol sodium succinate and iron(III) CPSS-Fe(III) as ion pair complex, with four plasticizers Di-butyl phosphate (DBP); Di-butyl phthalate (DBPH); Di-octyl phthalate (DOP); Tri-butyl phosphate (TBP); in PVC matrix . These electrodes give Nernstian and sub-Nernstian slopes (19.79, 24.60, 16.01 and 13.82mV/decade) and linear ranges from (1x10-5-1x10-2 M, 1x10-5-1x10-2 M, 1x10-6-1x10-2 M and 1x10-5-1x10-2 M) respectively. The best electrode was based on DBP plasticizer which gave a slope 19.79 mV/decade, correlation coefficient 0.9999, detection limit of 9×10-6 M, lifetime 37 day displayed good stability and reproducibility and used to determine
... Show More
The aim of this study was to evaluate the possibility of using Staphylococcus epidermidis cells as a probiotic to treat some skin infections. For this purpose, S. epidermidis Y73, which is an active bacteriocin producer and non-biofilm forming isolate, was selected among 134 skin isolates through primary and secondary screening. Tryptic soya broth was selected as the best medium to support bacteriocin production, while the optimal pH and temperature for S. epidermidis Y73 growth were 7 and 37°C, respectively, which were invested in the formula preparation. Furthermore, the possibility of using this isolate as a probiotic was investigated by preparing 4 potential cellulosic pads with 4 different formulae whic
... Show More
(2)
(1)
This aim of this study is to assess the Tigris River sediments and utilize them as a new abrasive for the preparation of polished surface of magnetite ore to be studied under reflected light ore microscope. Such polishing process was tested using 250, 125, 71, 45, 25 and 18μm grain sizes of the river sediments. For the completion of the polishing and to obtain a glossy perfect polished surface, the 7 and 2.5 μm sized standard diamond pastes were used. After each polishing stage, the reflectance and roughness of these surfaces were measured as an evaluation step for the polishing efficiency. The reflectance values (R%) of the magnetite surface were found to be reversely proportioned to the abrasive grain size; while the surface roughnes
... Show MoreAbstract
The purpose of the present paper is to light on the relationship between jobs design, analysis and its reflections on reinforcing workers' vocational adjustment. The present paper aims to accomplish cognitive and applied goals, top of which, test of functional analysis ability to have effect upon workers' vocational adjustment via job design directly and indirectly owning to the virtual factor practiced by these practices on the sought organization. The problem of the present paper comes with many, the most important is the of how to bolster and back up worker's technical adjustment through good and accurate design for the job.
Based on this problem and goals as to expla
... Show More