Probit analysis is a type of regression used to analyze the relationship between a stimulus and the quantal response. Allelopathy refers to direct or indirect negative or positive effects of one plant on another through the release of chemical compounds into the environment. This study was carried out to apply probit analysis in investigating the allelopathic effects of the leaves aqueous extracts of apple of Sodom [Calotropis procera (Aiton) W.T.] on the inhibition of seed germination of African rattlebox (Crotalaria saltiana Andr.). A laboratory experiments were carried out at the Faculty of Agricultural Sciences, University of Gezira, Sudan in season 2014/15. Ten concentrations (2.3, 4.6, 7.0, 9.3, 11.6, 13.9, 16.2, 18.5, 20.8 and 23.2 g/l) leaves aqueous extract of apple of Sodom were prepared from the stock solution (50 g / l). A control with sterilized-distilled water was included for comparison. Treatments were arranged in completely randomized design with four replicates. The seeds were examined for inhibition (%) in germination at three days after initial germination. Collected data were transformed using Abbott’s formula and subjected to probit analysis procedure (P £ 0.5). The results showed that the leaves aqueous extract of apple of Sadom had allelopathic effects on seed germination of African rattlebox and there was direct positive relationship between concentration (g/l) and inhibition (%). Also, the data indicated that plotting of corrected inhibition (%) against concentration (%) formed a sigmoid curve. Probit analysis transformed the sigmoid concentration-response curve to a straight line. Hence, the LC25 (2.16 g/l), LC50 (8.55 g/l) and LC75 (33.88 g/l) were accurately estimated. It was concluded that probit analysis is appropriate procedure in studying the allelopathy phenomenon.
This work aims to provide a statistical analysis of metal removal during the Magnetic Abrasive Finishing process (MAF) and find out the mathematical model which describes the relationship between the process parameters and metal removal, also estimate the impact of the parameters on metal removal. In this study, the single point incremental forming was used to form the truncated cone made of low carbon steel (1008-AISI) based on the Z-level tool path. Then the finishing was accomplished using a magnetic abrasive process based on the Box-Behnken design of the experiment using Minitab 17 software was used to finish the surface of the formed truncated cone. The influences of different parameters (feed rate, machining step s
... Show More
(3)
In the current study, the emission spectra generated from clove were measured under normal atmospheric pressure with different laser energies. Clove is used as a source of essential oil in herbal medicine, in particular as a dynamic analgesic oil in dental and other diseases. For aromatherapy, Antiseptic, antiviral, and antimicrobial agents are also packaged with cloves. Compounds that reduce inflammation tend to battle sore throats, cold, and cough as they display so many advantages. The measured spectrum reveals distinctive lines of clove’s chemical elements. X-ray fluorescent (XRF) and atomic absorption spectrometry (AAS) were used to measure the spectrum generated or absorbed by detecting the presence of va
... Show More
(14)
(5)
(2)
(1)
(1)
The present study focused mainly on the vibration analysis of composite laminated plates subjected to
thermal and mechanical loads or without any load (free vibration). Natural frequency and dynamic
response are analyzed by analytical, numerical and experimental analysis (by using impact hammer) for
different cases. The experimental investigation is to manufacture the laminates and to find mechanical
and thermal properties of glass-polyester such as longitudinal, transverse young modulus, shear modulus,
longitudinal and transverse thermal expansion and thermal conductivity. The vibration test carried to
find the three natural frequencies of plate. The design parameters of the laminates such as aspect ratio,
thickness
(1)
Shiranish Formation (Late Campanian- Maastrichtian) that cropping out north east Iraq, is studied by microfacies analysis of 52 thin section collected from Hijran Section, about 10 km west Shaqlawa Town, Governorate of Erbil. According to petrography, mineralogy and organic contents, rocks are subdivided to crystalline carbonate and microfacies units (biowackstone, packstone, and mudstone facies). Biowackstone facies have high ratio of the rock components, while the other facies have low ratio. Microfacies analysis led to relatively quiet deep marine environment.
This study shows the effects of copper material electrode, applied voltage, and different pressure values on electrical discharge plasma. The purpose of the work is the application of the spectral analysis method to obtain accurate results of nitrogen plasma parameters. By using the optical emission spectroscopy (OES), many N2 molecular spectra peaks appeared in the range from 300 to 480 nm. Also, some additional peaks were recorded, corresponding to atomic and ionic lines for nitrogen, target material, and hydrogen, in all samples. The electron density (ne) was calculated from the measurement of Stark broadening effect, which was found to decrease with increasing pressure from 0.1 mba
... Show More
(14)
(3)
(4)
Buckling analysis of composite laminates for critical thermal (uniform and linear) and mechanical loads is reported here. The objective of this work is to carry out theoretical investigation of buckling analysis of composite plates under thermomechanical loads, and experimental investigation under mechanical loads. The analytical investigation involved certain mathematical preliminaries, a study of equations of orthotropic elasticity for classical laminated plate theory (CLPT), higher order shear deformation plate theory (HSDT) , and numerical analysis (Finite element method), then the equation of motion are derived and solved using Navier method and Levy method for symmetric and anti-symmetric cross-ply and angle-ply laminated plates t
... Show MoreThe present work covers the Face-Hobbing method for generation and simulation of meshing of Face hobbed hypoid gear drive. In this work the generation process of hobbed hypoid gear has been achieved by determination of the generation function of blade cutter. The teeth surfaces have been drawn depending on the simulation of the cutting process and the head cutter motion. Tooth contact analysis (TCA) of such gear drive is presented to evaluate analytically the transmission error function for concave and convex tooth side due to misalignment errors. TCA results show that the gear is very sensitive to misalignment errors and
the increasing of the gear teeth number decrease the transmission error for both concave and convex tooth sides a
(2)