2D Electrical Resistivity has been applied at three selecting areas within the study area using Dipole-dipole and Wenner arrays with an a-spacing of 1 m, and the profile length was 120 m for both. The total data points were 4455 reads for Dipole-dipole, and the total data points for Wenner were 2340 reads, and the depth of each array was 15.4 m and 20.2 m, respectively. The 2D inverse results indicate the resistivity anomalies approximately at depth (2 - 7.8) m formed as a weakness zone lies within the quaternary and Injana Formation deposits and interbedded with secondary gypsum and gypcretes. Additionally, the inverse resistivity distribution model demonstrated that the area is impacted by groundwater that is interaction with sand, silt, and clay of the subsurface layers due to the gypsiferous and gypcrete deposits. They are distinguished by their ability to interact with water, whether it is surface or underground, and as a result, cause the emergence of a set of cavities and voids that may be filled with sediments that contain high levels of water and cause soil to wet. As well, the investigation gives the ideal array as Dipole-dipole rather than Wenner array due to its better in signal to noise ratio and provides the most suitable resolution for these applications, as well as the study, recommends conducting engineering and site investigations of the soil and determining the type of soil and the appropriate treatment methods that can overcome these problems.
Seismic facies analysis constrained with well log information have been used to predict lithofacies distribution across the Okam Field of Niger Delta. Density and gamma ray logs were cross-plotted and the seismic section was subdivided vertically into different seismic facies. The delineated lithologies, from well logs were correlated with seismic facies signatures using lines of intersection across the wells. Gamma ray and resistivity logs were used to identify the interfaces between the lithofacies and correlated across the field. Structural interpretation was carried out. Time slices were generated and examined at different intervals within the identified reservoirs. Stratigraphic related attribute and envelope were extracted on these
... Show MoreCopper Zinc Sulphide (Cu0.5Zn0.5S) alloy and thin films were fabricated in a vacuum. Nano crystallized (CZS) film with thick 450±20 nm was deposit at substrates glasses using thermal evaporation technique below ~ 2 × 10− 5 mbar vacuum to investigated the films structural, morphological and optical properties depended on annealing temperatures ( as-deposited, 423, 523 and 623) K for one hour. The influences annealed temperature on structurally besides morphologically characteristics on these films were investigated using XRD and AFM respectively. XRD confirms the formation a mixed hexagonal phase of CuS-ZnS in (102) direction with polycrystalline in nature having very fine crystallites size varying from (5.5-13.09) nm. AFM analys
... Show MoreIn the current study, the researchers have been obtained Bayes estimators for the shape and scale parameters of Gamma distribution under the precautionary loss function, assuming the priors, represented by Gamma and Exponential priors for the shape and scale parameters respectively. Moment, Maximum likelihood estimators and Lindley’s approximation have been used effectively in Bayesian estimation.
Based on Monte Carlo simulation method, those estimators are compared depending on the mean squared errors (MSE’s). The results show that, the performance of Bayes estimator under precautionary loss function with Gamma and Exponential priors is better than other estimates in all cases.
The finishing operation of the electrochemical finishing technology (ECF) for tube of steel was investigated In this study. Experimental procedures included qualitative
and quantitative analyses for surface roughness and material removal. Qualitative analyses utilized finishing optimization of a specific specimen in various design and operating conditions; value of gap from 0.2 to 10mm, flow rate of electrolytes from 5 to 15liter/min, finishing time from 1 to 4min and the applied voltage from 6 to 12v, to find out the value of surface roughness and material removal at each electrochemical state. From the measured material removal for each process state was used to verify the relationship with finishing time of work piece. Electrochemi
Several correlations have been proposed for bubble point pressure, however, the correlations could not predict bubble point pressure accurately over the wide range of operating conditions. This study presents Artificial Neural Network (ANN) model for predicting the bubble point pressure especially for oil fields in Iraq. The most affecting parameters were used as the input layer to the network. Those were reservoir temperature, oil gravity, solution gas-oil ratio and gas relative density. The model was developed using 104 real data points collected from Iraqi reservoirs. The data was divided into two groups: the first was used to train the ANN model, and the second was used to test the model to evaluate their accuracy and trend stability
... Show MoreBackground: Coronavirus is an enveloped RNA virus, from the genus Betacoronavirus, that is distributed in birds, humans, and other mammals. WHO has named the novel coronavirus disease as COVID-19.
Objective: We have conducted this review to focus on the studies that assessed the treatment efficacy and safety of Coronavirus (COVID-19) to describe its relation with the clinical outcomes of patients.
Method: PubMed, was searched for studies on the clinical evaluation of selected currently used treatments for COVID-19. we included six studies about therapeutic activity of chloroquine/hydroxychloroquine, two case series about oseltamivir and three studies about lopinavir/riton
... Show MoreClinical keratoconus (KCN) detection is a challenging and time-consuming task. In the diagnosis process, ophthalmologists must revise demographic and clinical ophthalmic examinations. The latter include slit-lamb, corneal topographic maps, and Pentacam indices (PI). We propose an Ensemble of Deep Transfer Learning (EDTL) based on corneal topographic maps. We consider four pretrained networks, SqueezeNet (SqN), AlexNet (AN), ShuffleNet (SfN), and MobileNet-v2 (MN), and fine-tune them on a dataset of KCN and normal cases, each including four topographic maps. We also consider a PI classifier. Then, our EDTL method combines the output probabilities of each of the five classifiers to obtain a decision b
In this work, an anti-reflection coating was prepared in the region (400-1000) nm of wavelength, with a double layer of silicon dioxide (SiO2) as an inner layer and the second layer of the mixture (SiO2) and titanium dioxide (TiO2) with certain ratios, as an outer layer using the chemical spraying method with a number of 6 sprays of layer SiO2 and 12 sprays of layer SiO2 - TiO2. Using the method of chemical spraying deposited on the glass as a substrate with a different number of sprays of SiO2, and a fixed number of TiO2-SiO2. The optical and structural properties were determined using UV-Vis spectroscopy and atomic force mi
... Show MoreMedicines comprising fosfomycin are prescribed for urinary tract infections. These drugs are available for oral use as tromethamine and calcium, while fosfomycin-sodium and disodium are given for intravenous (IV) and intramuscular (IM). Many quantitative analytical methods have been reported to estimate Fosfomycin in blood, urine, plasma, serum, and pharmaceutical dosage formulations. Some techniques were spectrophotometric, mass spectrometry, gas chromatography, high-performance liquid chromatography, and electrochemical methods. Here we perform a rapid narrative review that discusses and comparison between them of various analytical methods for the determination of Fosfomycin-containing drugs.
Several attempts have been made to modify the quasi-Newton condition in order to obtain rapid convergence with complete properties (symmetric and positive definite) of the inverse of Hessian matrix (second derivative of the objective function). There are many unconstrained optimization methods that do not generate positive definiteness of the inverse of Hessian matrix. One of those methods is the symmetric rank 1( H-version) update (SR1 update), where this update satisfies the quasi-Newton condition and the symmetric property of inverse of Hessian matrix, but does not preserve the positive definite property of the inverse of Hessian matrix where the initial inverse of Hessian matrix is positive definiteness. The positive definite prope
... Show More