This aim of this study is to assess the Tigris River sediments and utilize them as a new abrasive for the preparation of polished surface of magnetite ore to be studied under reflected light ore microscope. Such polishing process was tested using 250, 125, 71, 45, 25 and 18μm grain sizes of the river sediments. For the completion of the polishing and to obtain a glossy perfect polished surface, the 7 and 2.5 μm sized standard diamond pastes were used. After each polishing stage, the reflectance and roughness of these surfaces were measured as an evaluation step for the polishing efficiency. The reflectance values (R%) of the magnetite surface were found to be reversely proportioned to the abrasive grain size; while the surface roughness values (Ra) showed positive relationship with the grain size. The polished surface showed gradual improvement with decreasing grain size of the abrasive. The reflectance increased at a rate of 0, 0, 0.3, 1.2, 2.5, 3.7, 9.3, 20% with reducing grain sizes from 250, 125, 70, 45, 25, 18, 7 and 2.5 µm; at the same time, the roughness reduced at a rate of 72.2, 51.8, 23.7, 17.2, 10.9, 7.5, 6, 3.8 with reducing grain size. The 18 µm abrasive grain size of river sediments was found to be the best. Buffing by 2.5 µm diamond paste as the last stage, improved the polishing efficiency and resulted in 20% reflectance. Based on the obtained results, the Tigris sediments can be considered as fine-grained granules with the ability of preparing a flat, homogeneous surface with little roughness and reasonable degree of reflectivity.
A free convective heat transfer from the inside surface of a uniformly heated vertical circular tube has been experimentally investigated under a constant wall heat flux boundary condition for laminar air flow in the ranges of RaL from 6.9108 to 5109. The effect of the different sections (restrictions) lengths placed at the exit of the heated tube on the surface temperature distribution, the local and average heat transfer coefficients were examined. The experimental apparatus consists of aluminum circular tube with 900 mm length and 30 mm inside diameter (L/D=30). The exit sections (restrictions) were included circular tubes having the same inside diameter as the heated tube but with different lengths of
... Show MoreResearch Summary
It highlights the importance of assessing the demand for money function in Iraq through the understanding of the relationship between him and affecting the variables by searching the stability of this function and the extent of their influence in the Iraqi dinar exchange rate in order to know the amount of their contribution to the monetary policies of the Iraqi economy fee, as well as through study behavior of the demand for money function in Iraq and analyze the determinants of the demand for money for the period 1991-2013 and the impact of these determinants in the demand for money in Iraq.
And that the problem that we face is how to estimate the total demand for money in
... Show More
This research means a study (the impact of the Arab-Islamic environment on contemporary painting, the artist Abd al-Rahman al-Suleiman as a model). The research falls into two axes: the first: the theoretical axis, and the second: the applied axis. The first axis dealt with an introduction that contained: (the research problem, its importance, its goal, its limits, and the definition of terms). This research aims to uncover (the impact of the Arab-Islamic environment on contemporary painting, and the artist Suleiman was a model). And the research limits spatially: Saudi Arabia, and temporally: 2010-2014. This theme included two topics: The first: the characteristics of the Saudi environment and its impact on art. The second: the s
... Show More
In this work lactone (1) was prepared from the reaction of p-nitro phenyl hydrazine with ethylacetoacetate, which upon treatment with benzoyl chloride afforded the lactame (2). The reaction of (2) with 2-amino phenol produced a new Schiff base (L) in good yield. Complexes of V(IV), Zr(IV), Rh(III), Pd(II), Cd(II) and Hg(II) with the new Schiff base (L) have been prepared. The compounds (1, 2) were characterized by FT-IR and UV spectroscopy, as well as characterizing ligand (L) by the same techniques with elemental analysis (C.H.N) and (1H-NMR). The prepared complexes were identified and their structural geometries were suggested by using elemental analysis (C.H.N), flame atomic absorption technique, FT-IR and UV-Vis spectroscopy, in additio
... Show More
NH3 gas sensor was fabricated based on deposited of Functionalized Multi-Walled Carbon Nanotubes (MWCNTs-OH) suspension on filter paper substrates using suspension filtration method. The structural, morphological and optical properties of the MWCNTs film were characterized by XRD, AFM and FTIR techniques. XRD measurement confirmed that the structure of MWCNTs is not affected by the preparation method. The AFM images reflected highly ordered network in the form of a mat. The functional groups and types of bonding have appeared in the FTIR spectra. The fingerprint (C-C stretch) of MWCNTs appears in 1365 cm-1, and the backbone of CNTs observed at 1645 cm-1. A homemade sensi
... Show More
(16)
(14)
In this work, Schiff base ligands L1: N, N-bis (2-hydroxy-1-naphthaldehyde) hydrazine, L2: N, N-bis (salicylidene) hydrazine, and L3:N –salicylidene- hydrazine were synthesized by condensation reaction. The prepared ligands were reacted with specific divalent metal ions such as (Mn2+, Fe2+, Ni2+) to prepare their complexes. The ligands and complexes were characterized by C.H.N, FT-IR, UV-Vis, solubility, melting point and magnetic susceptibility measurements. The results show that the ligands of complexes (Mn2+, Fe2+) have octahedral geometry while the ligands of complexes (Ni2+) have tetrahedral geometry.
A new Macrocyclic Schiff base ligand Bis[4-hydroxy(1,2-ethylene-dioxidebenzylidene) pheylenediamine] [H2L] and its complexes with (Co(II) , Ni(II) , Cu(II) , Zn(II) and Cd(II)) are reported . The ligand was prepared in two steps,in the first step a solution of (o-phenylene diamine) in methanol react under reflux with (2,4-dihydroxybenzylaldeyed) to give an (intermediatecompound) [Bis-1,2 (2,4-dihydroxybenzylediene)pheylinediamine] which react in the second step with (1,2- dichloro ethane) giving the mentioned ligand.Then the complexes were synthesis of adding of corresponding metal salts to the solution of the ligand in methanol under reflux with 1:1 metal to ligand ratio. On the basis of, molar conductance, I.R., UV-Vis, chloride content a
... Show MoreThe aim of this work covers the synthesis and characterization of the new tertra dentate ligand (H4L) containing (N and O) as donor set atoms kind (N2O2) where: H4L=Bis-1,2 (2,4- dihydroxybenzylediene phylinediamine . The preparation of ligand contains reaction 2, 4 - Dihydroxy benzaldehyde and o-phenylene diamine . Schiff base was reacted with some metal ions in the presence of methanol to give the complexes in the general formula [M (H2L)] where: MII = Co, Ni, Cu, Zn, Cd. All compounds were characterized by spectroscopic methods I.R , U.V.-Vis, metal content and molar conductivity measurements, showed that the complexes are non-electrolyte. The proposed geometry for all of the proposed complexes was a tetrahedral while Ni complex was squa
... Show MoreIn this research the Inter-Particle Expectation Values have been studied for atomics Helium (He) and Beryllium (Be) also for He-like ions, Be-like ions (Li-1, B+1? Li+1, Be+2, B+3) by using Hartree-Fock wave functions, We compared the results to some ions which have the same atomic number from each group with atomic number, We compared the results with published calculations to the last studied .
In this research, an experimental study was conducted to high light the impact of the exterior shape of a cylindrical body on the forced and free convection heat transfer coefficients when the body is hold in the entrance of an air duct. The impact of changing the body location within the air duct and the air speed are also demonstrated. The cylinders were manufactured with circular, triangular and square sections of copper for its high thermal conductivity with appropriate dimensions, while maintaining the surface area of all shapes to be the same. Each cylinder was heated to a certain temperature and put inside the duct at certain locations. The temperature of the cylinder was then monitored. The heat transfer coefficient were then cal
... Show More