Fifty of urine samples were collected from patients with urinary tract infection
(UTI). The samples were collected from AL- Yarmuk hospital in Baghdad. All of
the isolates were diagnosed using biochemical test and vitek. The result showed that
30 (60%) isolates identified as E.coli from 50 urine samples. The colicinogenic
isolates were determined using cup assay methods. The results showed that 10 out of
30 isolates (33.3%) were detect as colicin producers from 30 isolate identified as
E.coli depending on the clear zone that observed against the sensitive isolate.
Colicin was extracted from the efficient isolate. Colicin activity (320 U/ml) was
determined by well assay method. The protein concentration (520 μg /ml) estimated
by using Bradford assay. The watery extract of Chilli papers (Capsicum baccatum)
was extracted and used it as reducing and capping agent for gold nanoparticles
synthesis. The characterization of the gold nanoparticles was done by UV-Visible
Spectrophotometer, Transmission Electron Microscope (TEM), and resulting
spherical nanoparticles with diameter ranging between (35-70 nm). The antibacterial
activity of colicin alone and gold nanoparticles alone and combination of colicin
with gold nanoparticles against ten isolates Pseudomonas aerugensa isolated from
burn samples, using tube method. The results showed that all the three treatment had
antibacterial activity but the combination of gold nanoparticles and colicin is better
than used each one separately.
(141)
In this work, the effect of the addition of bright nickel plating and silver carried out by the electroplating method has been studied, on the coating of copper nanoparticles on the copper base metal via the process of thermal evaporation. The improvement of the solar absorber using CuNP in combination with the bright nickel and silver was obtained to be better than copper nanoparticles individually. A bright nickel enhanced the absorbed thermal stability. Also, other optical properties, absorptions, and emissivity slightly decreased from (93% to 87%), while the existence of silver had a slight impact on absorption of about (86.50%). On the other hand, thermal conductivity was evaluated using hot disk analyzer. The results showed a good
... Show MoreAg nanoparticles were prepared using Nd:YAG laser from Ag matel in distilled water using different energies laser (100 and 600) mJ using 200 pulses, and study the effect of the preparation conditions on the structural characteristics of and then study the effect of nanoparticles on the rate of killing the two types of bacteria particles (Staph and E.coli). The goal is to prepare the nanoparticle effectively used to kill bacteria.
(2)
(146)
(145)
Metal oxide nanoparticles demonstrate uniqueness in various technical applications due to their suitable physiochemical properties. In particular, yttrium oxide nanoparticle(Y2O3NPs) is familiar for technical applications because of its higher dielectric constant and thermal stability. It is widely used as a host material for a variety of rare-earth dopants, biological imaging, and photodynamic therapies. In this investigation, yttrium oxide nanoparticles (Y2O3NPs) was used as an ecofriendly corrosion inhibitor through the use of scanning electron microscopy (SEM), Fourier transforms infrared spectroscopy (FT-IR), UV-Visible spectroscopy, X-ray diffraction (XRD), and energy dispersive X-ray spe
... Show More
(2)
(1)
Immune-mediated hepatitis is a severe impendence to human health, and no effective treatment is currently available. Therefore, new, safe, low-cost therapies are desperately required. Berbamine (BE), a natural substance obtained primarily from
This c
(10)
(7)
The research includes the synthesis and identification of the mixed ligands complexes of M 2 Ions in general composition ,[M(Leu) 2 (SMX)] Where L leucine (C 6 H 13 NO 2 )symbolized (LeuH) as a primary ligand and Sulfamethoxazole C 10 H 11 N 3 O 3 S) symbolized (SMX)) as a secondary ligand . The ligands and the metal chlorides were brought in to reaction at room temperature in(v/v) ethanol /water as solvent containing NaOH. The reaction required the following [(metal: 2(Na Leu --): (SMX )] molar ratios with M(II) ions, Were M ( Mn ( II),Co (II),Ni(II),Cu( II),Zn (II),Cd(II)and Hg( The UV Vis and magnetic moment data revealed an octahedral geometry around M(II), The conductivity data show a non electrolytic nature of the complexes . The
... Show MoreWheat (Triticum aestivum L.) is one of the Poaceae family (Gramineae). Is momentous for human nutrition, and the stresses can affect strongly on the phenotype characteristics of the plant. The aim of this study was to determine how electric shock on germinated grain (for 2.5, 5, and 7.5 mins.) and heat shock at ( 35 oC, 40 oC and 45 oC) applied after phase out the radical length of 2-5 mm, from the grain of two wheat Varieties: “Baghdad 1” and “Babylon 113”. The electric shock for 2.5 mins., lead to delay of flowering, from day to 50 % flowering was 93 day, as well as, gave lowest value of plant height 64.5cm and lowest spike length was 10.7 cm. While The highest flag leaf area was obtained by electric shock for 5 mins. was 56.6
... Show MoreNanoparticles of humic acid and iron oxide were impregnated on the inert sand to produce sorbent for treating groundwater contained of cadmium and copper ions by technology of permeable reactive barrier (PRB). Sewage sludge was the source of the humic acid to prepare the coated sand by humic acid—iron oxide (CSHAIO) sorbent; so, this work is consistent with sustainable development. For 10 mg/L metal concentration, batch tests at speed of 200 rpm signified that the removal efficiencies are greater than 90% at sorbent dosage 0.25 g/ 50 mL, pH 6 and contact time 1 h. The kinetic data was well described by the Pseudo first-order model indicating that physicosorption is the predominant mechanism. The maximum adsorption capacities (qmax) were c
... Show More
(9)
Background: The mechanical properties of 3D-printed denture base resins are crucial factors for determining the quality and performance of dentures inside a patient’s mouth. Tensile strength and diametral compressive strength are two properties that could play significant roles in assessing the suitability of a material. Although they measure different aspects of material behavior, a conceptual link exists between them in terms of overall material strength and resilience. Aim: This study aims to investigate the correlation between tensile strength and diametral compressive strength after incorporating 2% ZrO2 nanoparticles (NPs) by weight into 3D-printed denture base resin. Methods: A total of 40 specimens (20 dumbbell-shaped and
... Show More
(2)